粉丝5919获赞2.3万



in this video i show step by step instructions on how to install a car harness into your vehicle and what to do if you break or lose any of your car harness components when you are ordering your comma 3 you need to pick the right car harness that is compatible with your vehicle in order to get it to work this kit contains a harness an rj 45 cable and the comma power the comma 3 device itself comes with a c cable like you saw in one of my last videos, i got my windshield cracked by a rock and so it needs a replacement the day before the scheduled repair i removed my comma device and all the components that i had installed all the hardware can be reused only the windshield mount will need some new double sided tape installing all of the cables and harnesses back to my comma 2, but the installation process for the comma 3 will be the same and also if you are upgrading from the comma 2 to the comma 3 you won't need to buy a new car harness kit as long as you are still driving the same car i am installing this into my 2019 honda civic and first we need to remove the camera cover in order to do this i have adjusted my rear view camera down and i will remove the smaller cover first, i push it down and it comes off but also the right side of the main cover became a little bit loose for the entire installation process i think this part is where i struggled the most it almost seems like they didn't seal the right side of the cover correctly after a place my windshield and because of this i'm struggling for about three minutes just to get the left side of the cover free i don't want to use too much force because i'm afraid of breaking the plastic clips that are holding it together so i push the main cover back into position and i'll try again to remove it in one piece now after it sealed i try to push down and forward and it comes off right away and falls into my lap finally fortunately all the plastic clips are okay and i didn't break anything it's important to be patient and take your time so the cover is off and you can see the camera connector which i need to unclip on the top of the cable there's a small knob, which i push down and just pull the connector out now i'm going to connect comma's car harness which is specific to my vehicle to the honda camera these two will connect to the camera on the other side is the harness box for the rj 45 cable port to connect with my car's obd2 port and the c port is for the comma device here's the original clip that i unplugged before it will connect to the harness and the other end to the camera slide these in all the way and you will hear some audible clicks when it's perfectly snapped into place now i take the comma power and the rj 45 cable and i need to push the cable correctly into the port so that it clicks now the comma power is ready to be connected with the obd2 port the obd2 port is usually found within reach of the driver underneath the steering wheel, so i'm connecting the comma power to the obd ii port and i just push it in it may feel a little bit loose but actually it's holding the connector tightly in place and i hide the cable behind the plastic trim the cable will connect to the car harness that i installed before you can see that it hides beautifully behind this trim i continue to route the cable behind the weather trim, this takes a little bit of force to open the rubber trim and squeeze the cable in and also around the plastic trim just be careful not to damage the cable if you take your time the final result will be worth it it will look very clean and you won't see the cable after it's done and lastly let's route this around the windshield this part is very easy and the cable just pops behind the ceiling cover you can see it's nicely secured and hidden away all the way from the obd two port to the car's camera now we connect the rj 45 cable to the harness box it just clicks right in and connects the obdc cable and now i need to secure the harness when i first got my harness box it had two sided tape, but i don't have as much free space as they showed in comma's youtube installation video so i need to improvise and just squeeze it in and here's the other end of the obdc cable that connects to the comma device i route this in the same places as the automatic day night mirror harness right through the groove in the harness cover and once i'm done here i pop the main cover back into its position and i make sure it's tightly secured along with the trim it goes back into place just like this and there you have it the final product everything packed nicely under the cover the only visible cable will be the obdc cable that connects to your comma device next, you will need instructions on how to correctly install your windshield mount for your comma device i've provided a link to this information in the description below if you lose or break anything during the installation process you can buy new parts separately from comma ai's website and i also recommend that you check the comma ai's community discord server and therefore sale thread where other members are selling parts you can also use this if you want to sell anything yourself the link to join comma ai's discord server is also in the description down below that's it for now see you next time on let it drive。

