这是一台西伯利亚 s 二幺手游版的啊,它这个耳机什么问题呢?就是这是手游版的,就是三点五插头,可以直接连接手机。呃,当然我测试的话,我是用了一个逻辑 g 四三二的一个声卡,声卡去测试它,因为声卡去测试耳麦的话, 他的一个音效很好,可以听得很清楚,到底是麦克风坏了还是哪里哪里有问题?插头有问题,这是他原本的一个麦克风,你看他这个麦克风,这里已经已经快折断了,因为他经常这样弯折,折断了啊,这个线折断了。呃,然后我们剪的下来是这个麦克风里面,这里面声音不准确,很小,声音很小。 然后这是我们已经换了一个麦克风,换好的一个新的麦克风,这个机头梁比较有弹性,然后不好给大家展示啊,这套喇叭麦克风呢,我们已经换好了,你看刚才已经拆下来的这个麦克风,这个位置还没有,还没有那个拆下来,这是已经换好的一个新的麦克风。呃,我们 检查这个线没有问题啊,我们接下来呢就是测试,呃,测试一下这个麦克风它的声音效果,我当时我都是通过声卡去测试的,声音效果非常好。然后这这款耳机大家注意的时候就是这个麦克风,麦克风在这里使用的时候一定要小心,它,这里不要,不要折叠,你看我们它原本就是这样一个状态, 这里这里折断了,折断了,然后这个麦克风导致接触不良了,这是我们已经换好的,已经修好了,我准备给他装回去,然后给他寄回, 然后这里的线焊接的都没问题,然后他的麦克风正负极不要碰到一起啊,现在就可以装装机,然后准备好好接回,这是他的一些螺丝啊,我们都 要给他组装好。其实这款耳机还是非常不错的,性价比很高的一款耳机,他有好几个版本。我在上期视频也讲到这款耳机,如果大家自己去维修更换的话,其实也很简单,只要有零配件就可以了。 拆机,然后就拆螺丝,拆螺丝当然也要涉及到需要焊接啊,如果你没有工具的话也修不了,要焊接,要配件,要会要会拆机, 还有还有最后一个螺丝,总共是五颗螺丝。 好嘞,装好了装好了,我们下一步就是把口罩给装好。好嘞,这个耳机就已经修好了啊,如果你们有需要修耳机的也可以联系我啊。本期视频就到这里,欢迎大家观看。
粉丝7475获赞1.4万

大家好,今天讲一下这个耳机如何更换耳罩啊?他是这里是首先是卡扣式的, 卸下来是这个样子,他耳罩是有几个卡眼,把这个拿下来,然后对准眼,把耳朵放上, 直接扔,最重要最低点装好就可以更换,非常简,简便简单。

将三 m 背胶撕下,对准耳机盖,然后将耳罩卡条卡进耳机的卡扣中,听见响声就是卡好了。 另外一只也是同样的方法,这样耳罩就完全安装好了。

大家好,今天收到一台西伯利亚 s 二幺入门级耳机啊,入门款?客户问题呢是右边听筒不良时响时候不响,自己拆开过啊。这耳机是一款电竞入门级耳机,入门首选。介绍一下。灯光控制,麦克风控制灯光麦克风控制。呃,这个是旋钮,要旋钮这一键静音啊。 客户描述问题是这个左边不响啊,右边不响右边不响。我猜错了,猜成左边了猜错了,你先把左边的恢复吧啊,先不恢复也可以。这个耳罩已经这样了啊,太脏了。 我们先给他拆一下右边看一下到底是什么问题啊。这种的一边不响,喇叭坏的可能性很大喇叭坏的可能性很大啊。 这是他的螺丝,先放边吧这是他的喇叭,现在右边是响的, 右边是响的。嗯,接上去左边看一下左边响不响。拆这个的时候这个线还是老生常谈的线,不能接错。 嗯,这边这边不响,可能他描描不错的。这个不应该是右边,是左边,左边不响啊, 左边不响我们我们给他那个给他用个喇叭试一下啊。我这拆了一个逻辑的喇,什么问题?他不响了啊?先把右边喇叭拆下来了,看一下什么问题。一边不响 这边不响。不响的问题点可能不是喇叭坏,而是它这个哪里接触不良啊。喇叭先放一边,我们检查一下它这个喇叭的线,它是金色和红色对应的是这边的这根。 哦,这两根线估计是问题点出在这里,这个本来是要测量一下从这里的线到这里的哪根线可能就是这里这里的哪根线接触不了,因为它的驱动在这里,芯片在这里,这个板子只是一个连接线的作用啊。我先把这个板子拆开来看一下,看它里面到底是否带芯片功能啊? 啊?不带,就是一个灯,就是一个灯光控制的。嗯,负极是共用一个负极,这两根线是共用一个负极,那说明他的问题就是在这个声卡到 耳机的线出了问题啊。声卡到耳机的线,那就是这两根线的这根线断了。应该是啊,这个蓝色的线断了。 我拿去测试一下啊。这边是正极,我那边做标记,负极先用他本来好的那个喇叭来试一下他的功能啊。 嗯,还是不响,你等一下打吧。还是不响还是不响,我们先把右边装回去。 嗯,装回去 这边已经有声音了,这边还是正常的。问题点不在这里啊。装回去 先把螺丝装回去,这边是好的, 右边都是好的。右边的线,这边是右边喇叭的。 难,比较难看的到啊,我就这样修啊。我们测量一下导通, 测量一下他是否导通啊?测,测量是测量这两个点。 嗯,我给大家看一下这两点。导通这两点不导通,这个点到这里导通就到这里,到这导通就是接,是接接负极的啊。这个导通,那就说明是这根蓝色的线,蓝色的线接触接触不良了。嗯,我把它拆了蓝色的线, 把这个换一下,看一下他喇叭先是否 测试先测试喇叭啊,这是把线,就是把左边的线跟右边的线同时接到,驱动一个喇叭,这样就是单声道,不是双声,双声道,我们先试喇叭是不是好的,这是修耳机的一个顺序啊啊?喇叭是好的, 喇叭是好的,喇叭是好的,那说明就是线出问题了,线出问题了我们就修线啊,什么出问题?我们修什么线?这里 这里他用了一个扎带捆绑住,我们把这个扎带剪掉, 哪个位置接触不好,就是从这种的,如果一边没声音就是驱动都是好的声音,灯光控制都是正常,然后一边不响,他的问题就从这里到这里,到这根线哪哪根接触不良啊。我们这种的先给他断电,断电之后先断电,断电之后放点音乐, 断电之后把这里看一下能不能拆了啊?能不能卷就是旋转让他卷出来, 嗯,不能卷,不能卷的话我们就要给他切开,切开之后不用切开,直接剪刀剪开,这里面肯定有一个金属环来扣住啊, 把这个环拿出来,然后这里这段 给他把皮剥开,无非就是这个问题和尾部那个问题啊,把皮剥开估计就会发现这边是否有问题啊? 呃,可能问题我已经知道了啊,现在给大家看一下,演示一下这边是一个什么样的情况啊? 你看我刚才测量到这边就是这根蓝色的线接触不良,因为他是换到左边喇叭的,你看这边这边有一根走线,走到这里那说明就是这个蓝色的线,我们现在来把这个蓝色的线给大家平着看一下,是否是蓝色的线已经快断了啊? 看到没有?这里蓝色的线已经断了啊,问题点已经找到了,这根线已经断了,就成这个了。这是一根布啊,他实际的线已经断了,我们把它剪断,剪断之后焊接,焊接好这个问题估计就解决了啊,我们看现在开始焊接, ok, 接好之后还要做一下绝缘的,就用这个布包起来, 麦克风的线也要包起来,不然他会出现那种电流声啊,杂音啊什么的啊。好了,那这种的拨开的我们就要用用胶水固定,给他拉开一点,拉长一点, 胶水已经没有了啊,胶水给我 这种地方必须要用五零二固定啊,因为五零二干的快,他又是塑料的, 我要你,你要 弄好之后给他拉一下固定, 干的快啊,现在试一下声音, ok 了, 这里看哈, 已经解决了,就是这两个线接受不了了,我们给他卡好之后一点痕迹没有,然后把这里盖好, 上螺丝。 西伯利亚 s 二幺啊,如果修了这一个问题,就说明大部分耳机的问题都是这样, 装好他的装好账啊, ok, 解决了,灯光正常正常,麦克风灯光正常,调节一下,熄灭灯光熄灭, ok, 音量旋钮正常。好的,这款耳机已经修好了,如果有同类问题的话可以找我解决。

耳机坏了,不要了,可能修修还能用。大家好,我是布洛芬,今天需要修理的是一个粉丝寄过来的 siri 寒冰 v 二的双洞之蓝, 他跟我说的是他的右耳是没有声音的,但是有时候插上是有声音,我根据这个故障排除的话,应该是线彩故障,而不是单元的故障。线彩无非就是头梁线或者是他的主线,但是我这边把它大卸八块以后发现他的线是没问题的, 把它单元拆下来以后测了一下,根本就没有组织,接上了一个喇叭 是有声音的,你说他的故障就发生在了他的幼儿单元上,这个单元也是用着用着莫名其妙就没有声音, 基本上这种功夫章,也就说经常大量的使用 最大音,有大声音播放的时候可能会造成他的引线啊,他的锻炼不停的震动啊,造成了金属疲劳。所以说这个故事还是比较常见的,之前也修复了几个,但耳没声音是但原故障导致的。这种耳机 以后使用的时候大家要注意不要用最大音量吧,一个是保护自己的耳机,一个是保护自己的听力, 等耳机单元到了以后给他换上基本上就可以了。我是布洛芬,我们下期见,拜拜。

接下来我们要开箱的是西伯利亚他们家出的两款无线耳机,那么咱们就先从这个开始拆啊,他的具体型号叫西伯利亚的雨,有收纳包,说明书,音频线,这是数据线,这就是耳机的本体啊。 首先这个耳机啊,侧面这有一个 nfc 的标识,现在真的很少有耳机在支持 nfc 模块了啊,这个先给一个好评啊。侧边这块是标准的这个音量加减,中间暂停键,三点五毫米耳机口,然后这边是一个 typec 口,还有这个 anc 主动降噪的一个开关。那我们废话不多说,先开机试一下啊, 音频编码是 aac。 然后我们看一下头梁金属了啊,做工方面的话我觉得还是不错了,蛋白皮这块非常的柔软厚度啊,包括这个弹性我觉得都是不错的。废话不多说,戴上听一看。 few moments later, 好,我大概听完了,我现在正好刚才没试他的降噪效果啊,他首先物理降噪就已经不错了,开一下主动降噪试试,降噪模式下的耳压还挺大的,通透模式的话会听到比日常多一些的白噪音啊,我再复听一下这个 a few moments later 我这都听完了,我给大家简单说一说啊,这款耳机的音质来说的话,它的信息量不是很大,然后低频反而做的并没有特别特别的量大管饱 力大声粗,然后中频的人生很前途。高频的话他依旧是没有什么特别高的噪音啊,就是 只能说高频的信息量相对来说是比较暗的。但是这款耳机整体的调音来说的话,我觉得就是只能用两个字来总结,就是保守打开它这根音频线吧,我试试这个有线耳机的音质吧。接上有线模式 给大家服听一下啊, a few moments later 哦,我服听了一下啊,就是他有线模式的这个听感信息量不高了,这个短板是补上了。如果说你是以有线模式为主, 我只是想要一副不带式耳机,又能兼顾我的有线模式使用,又能兼顾无线模式通勤使用的话,那么你买这个西伯利亚的鱼没毛病。关于这个西伯利亚的鱼的这个头戴式加大耳机的开箱,我们就先到这里。

今天我们修的是一台西伯利 s 二幺幺,然后这款耳机的问题是这个音量旋钮坏掉了啊,音量旋钮它里面接触不良了,调音量的时候会有沙沙声的响 啊,我们维修呢,是可以更换这个音量调节的键啊,我是直接把这个板子换下来,因为我正好有这种配件。我首先来给大家介绍一下这款耳机吧, 他这个也比较脏了,然后客户也没有叫我们给他清洗啊,我们也没有做清洗啊,这是一个音量调节旋钮,这是一个那个麦克风的麦克风的调节,我给他上电试一下哈。 好,这款耳机已经充电了,如果插上电的话,他试起来可能效果会比较好啊,他已经有灯光效果了,这个是麦克风,这个是灯光啊,你看他灯光可以调节开和关 音量旋钮,然后这边是一个静音键啊,这款耳机它的一个问题就在这个音量旋钮,所以我们把它换掉了啊,我讲下这款耳机吧,这款耳机还是性价比,我觉得数得上前前一前二了啊,在同类别的同价格的里面数数一数二的一个耳机了。 首先它比较轻盈这两个,这两个它有一个收缩性,可以夹住我的感觉不会掉落,然后它这个头梁也是一个钢丝的,它不会坏啊,非常轻巧,然后带一个 lg 的那个灯光袖,然后这个皮质的线也是带了全程保护的,然后也不会断。 然后唯一的问题点就在这个音量旋钮这里,因为他经常旋钮啊,旋转他就呃旋转过头了。还有一个唯一的亮点就在这里,你看这款耳机他没有一个麦克风,他其实是一个隐藏式的麦克风,你看他麦克风在这里啊,他直接是一个内置麦克风,这在同类别的耳机里面这样做只有在只有在那种 运动耳机或者说是休闲耳机,比如 bose 的,呃, bose 的那个 q c a 系列,还有那个苹果的 beast 的那个,呃,录音师啊, solo 之类的耳机,会做一个内置的一个耳耳麦哦。呃, 这个作为一款游戏耳机,他能够把耳麦做成这样已经是非常不错了,非常良心哈,这款耳机还是很能打的。呃,我比较推荐啊, 如果你们有这种问题的也可以找我找我找我给你修。好吧,我们测试的时候,呃,也是已经测试好了,灯光啊,麦克风啊,静音啊,音量旋钮啊都是 ok 的哈。好,本期视频就讲这把,如果你们有耳机需要的维修啊,就可以跟小区联系啊,再见。

上次教大家换耳罩的视频讲的可能不够详细哎,今天突然有人来和我说,根据我教程来拆坏了, 嗯,再给他处理。换新之后,哎,我决定再录一次,再次详细一点。首先随便找一个角扣开,听到咔的一声就停,哎,不要大力出奇迹了,会断的。 然后换一边,最好是对角线一样,听到咔的一声就停,再换一个角, 四个角都咔过了,耳罩自然就下来了。把塑胶料上面原本的耳罩取下,换上新的, 在着装孔按上去就好。最后可以拉一拉,确保是否装好了,各位学费了吗?


当耳罩出现损坏想更换时却不方便拆卸,看看这款升级版西伯利亚 s 二十一磁吸,快拆耳罩哦!在想更换耳罩时,方便快捷,想怎么换就怎么换。出色的蛋白皮耳罩,不但柔软舒适,贴合耳部,还能提升使用寿命。这样一款游戏性能出色还如此方便的耳机,真的可以充!

东方来袭不能错过的好耳机,今天来给大伙裁个重量级的家伙,西伯利亚 g 零二无线充电坐板, 我就是玩, 想了解的点个关注下个视频分解或者进波波间。

今天开一款西伯利亚入耳式游戏耳机,这款耳机手机电脑通用,一起来看看吧。 这个是开机版本, 这个是三点五毫米版本,两款外观上没有区别, 唯一不同就是插头用三点五版给大家展示一下吧。一个独立麦克风, 右边是万科坡,有电气风。 一体式的耳挂结构,佩戴更牢固。 多功能集成线控集成麦克风,日常语言通话,可播插麦克风玩游戏。安装大神就是你了。双麦设计, 三点五版本制作一条一点二英雄线,手机干扣笔记本、台式机都可以使用, 看下佩戴效果吧。

拆机后重装会不会影响它的防水性能呢?上次呢御姐拆了一台 soohouto 啊,今天我们呢去复原一下,再看看它的防水性能呢,能不能做到跟新机一样的品质, 后盖一旦被拆了呢,他的防水胶贴呢就会变形,达不到心机一样的品质。来,我们去织材布理料去啊,这一个呢就是我们的织材仓来的哦,全部都是的啊,我来看一下我们的 soo 和织材放在哪个区 哦?一区的零二零二。来我们一起去看一下,在这里这里对,这里是一区。 哇哦,这这一整箱都是的哦, soo 的防水胶贴,这一袋也是让我拿开看一下哇,都有原装的,包装盒都是有的哦, 看一下啊,都是原装的,来我拿一个随便拿个出来给你们看一下啊,这些黑色的就是防水胶贴,连我们的测试防水的之材都也在哦,来我们拿着就是这个了。来我们去看一下,把手机复原一下来, 首先呢我们要把手机放在专业的加热器上面呢,去加热他这里的温度呢,我已经调好了啊,大家看过来,然后我们要把手机边框这里拆的那些胶呢,把它清理干净才可以,整个内部大家看得到他是蛮干净的啊,没有什么胶。 然后呢这个就是加热过的,我们把那个原装的防水胶贴贴上去就可以了哦,朋友们看过来, 现在呢就把后盖接回去,然后呢我们复原一下啊,这个 就是能够做到跟心机一样的品质的话,能做到防水哦,哎, ok。 然后呢我们要去用专业的按压器上面呢去对他进行一个后盖贴合,看一下,这些就是我们专业的按压器来的, 这里呢是我们 sroco 的一个模具,专业的就是专业的把他说对吧?然后我们要把手机放到模具里面去对他进行一个按压, 然后放到我们这个仪器上面去压他就可以了啊,打扑克 倒计时一分钟,一分钟之后呢他就后盖呢就服帖了啊, 来这一台呢就是我们 soto 已经帮大家重新装好了啊,然后呢我们现在拿过去用专业的仪器呢帮大家测试一下它的一个防水器密,这一台呢就是我们专业的 gd 测试平台啊,来我们给我们的 sooto 呢测试一下它的一个防水性能 来,我们现在呢开始测试防水啊,御姐呢要把这一个我们的卡槽呢拆出来,然后呢把我们这个防水胶圈给贴上去,因为他在这个地方呢有 一个排气孔啊,是为了堵住,之后呢就可以维持手机的一个亲密点开左上方的呢这一个按钮,然后呢按住中间 把卡槽推进去,然后呢他上面就会有一个测试防水的一个气压在跳动了啊, 大家等待一下啊,这就是整个在测试防水哦,大家看得到啊,防水测试已通过,下一步呢就是测试相机了,如果说大家想了解更多的关注玉姐。

这个,今天又要拆盲盒了,每天拆盲盒感觉好刺激!这是这是哪里的?云南?这是云南的粉丝寄过来的,看看这个盲盒里面是什么啊? 每天拆盲盒好刺激啊!手机,耳机,摘下耳机 啊,这是西伯利亚的,西伯利亚的 s 二幺,这是这耳机怎么了啊?卧槽,麦克风断了,给他修一下 的泪珠儿。


天气越来越热,还在担心你的手机成为暖手宝?请跟随我们的拆姐一起探究 srltrud 散热大招吧!首先关机,取出 sim 卡托加热手机背面,然后用拆机片小心拆卸后盖。 取下无线充电线圈和 nfc, 挑开连接主板和副版的 fpc 线路板, 取下天线,取下主板。主板背面屏蔽罩包围的就是手机处理器, 处理器上面的白色涂层是更快传导热量的凝胶 team。 凝胶 team 的上面是柔性纤维的纳米 team, 相比上一代 team, 凝胶 team 的热传导率提升了三点五倍。纳米 team 不易变形,热传导率更高。 让我们继续拆解,小心取下电池加热分离屏幕, 揭开灰色的散热石墨片,露出的 vc 君热板覆盖了从电路板到电池的区域。介绍了这么多,让我们串联一下 s 二 o truck 的散热接力。众所周知,手机处理器是手机发热的主要热源,热量从处理器热量接力传导, 经过凝胶 team、 纳米 teamvc 均热板,再到散热石墨片的层层接力,将热量快速分散,使手机处于可控温度范围内。关于散热,你还想知道哪些知识?

this is the samsung galaxy s twenty two plus disassembly if you want to see more videos like this make sure you subscribe and follow me on twitter so you'd be notified when i upload a new video and if you need any tools there are links in the description first, is some training is to be removed next we need to apply heat to the back plate using a hair dryer or a heat gun to loosen up the adhesive underneath and then we're going to use a plastic pry tool to pry the back plate off here's a better look at the glass back plate, the glass camera lens covers can be replaced by playing gate and prying them off the aluminum frame or camera bezel can also be pride off but it requires to remove the back plate on the back, we can see the other side of the aluminum frame which is basically tucked underneath and to the back class and on the flash diffuser there's a hole for the back microphone and there's a small pathway inside which picks up sound from the ring of the flash diffuser there are nineteen phillips screws that need to be removed now the flex cable for the wireless charging coil and the nfc antenna need to be disconnected and then the graphite film or the bottom speaker sampling needs to be peeled off the wireless charging coil is located in the center and the nfc antenna is located on top there's also a large graphite foam covering them to help transfer heat here's a look at the other side now that we have access to the battery cable we can disconnect it once the battery cable is disconnected we can proceed to this connect the rest of the cables the top plastic cover can also be removed there are some antenna lines on this plastic cover, which are those light, gray color lines here's a look at the other side the front facing camera can be disconnected however is glued in place at this point, the main board can be lifted up and removed looking at the main board there's a twelve megapixel ultra widelands of fifty megapixel, white angle lens and a ten megapixel telephoto lens only the white angle and telephoto lens have ois or optical image stabilization there's a secondary microphone located on the top corner and the led flash and light center located below the main board is a dual layer board design the camera connectors are located on the back and they can be disconnected by just popping them off the proximity sensors located next to the top camera connector and there's graphite film on the back shield to help transfer heat the third microphone is located right here and that's the microphone for the back which picks up sound from the flash diffuser once the graphite film is peeled back we can see thermal paste on top of the ram and processor here's a better look with the thermal paste cleaned off there's a single phillips screw, which is holding down the top speaker assembly now the speaker assembly can be lifted up and removed the top speaker assembly has a little white foam ball underneath the blue tape and here's a look at the other side now the bottom speaker assembly can be removed here's a better look at that and the speaker assembly also has the little white foam balls and there is a thermal pad underneath the speaker assembly as well now as far as the linear vibrator motor or haptic feedback motor when i first active as twenty two apart, i didn't even see it, so i totally forgot to look for it and then later on when i looked at the video, i thought it was between the screen and the frame on the bottom portion of the phone, but actually a few people pointed it out in the comments that the flex cable for the speaker assembly does have four more contacts instead of just two so i tested it out and i removed the speaker assembly and then when i powered on the phone there was no vibrate and then when i installed the speaker assembly again and power the phone on the vibrate feature worked, so the motor is actually located in the speaker assembly itself and is closed off so i'd have to actually tear the speaker assembly apart to see it there's glue all around the speaker assembly itself which is adhering it to this plastic piece so the vibrator motor would be located on this back part of the speaker assembly now the flex cable connecting the main board to the screen can be disconnected, so if you need to replace your screen there are two ways you can do it you can heat up the front of the phone and just pry the screen off from the front or you can take the back plate off and remove the screws on the bottom speaker assembly and remove that speaker assembly, so you can you can disconnect the flexible for the screen this way and then once you have that flexible disconnected you can pry your old screen off apply new adhesive and reply your new screen and just resemble the phone obviously just prying the screen off from the front would be the easiest method however, it might be a little bit difficult trying to seat the replacement screen perfectly so the cable connector will just connect when you pushing it down now we're going to disconnect the two flex cables to connect the main board to the subboard, there are three phillips screws, which are holding on the sub board that need to be removed now the sub board can be lifted up and removed the primary microphones located here and there's a red ribber gasket around the charger port the sim reader is located on the back now onto the battery there are no pool taps provided to help pride the battery off, so we're going to do some ice or propol alcohol and apply some to the sides of the battery and let us sit there for about thirty seconds so each way that he's have underneath the battery make it easier to pry it off here's a better look at the four thousand five hundred milliamp hour battery once the battery is removed we have a better look at the copper vapor chamber which runs underneath the battery as well as the motherboard now comparing this with the design of that has twenty two that has twenty two had three d graphite which is layers of graphite to help transfer heat once the film on the bottom is removed we can see the indisplay fingerprint sensor there's a liquid damage indicator which is a wide sticker on the bottom and there's a rubber gasket a mesh filter for the speaker openings on the bottom and top with the frame as well as the microphone openings and for those of you who might have accidentally stuck your simijector tool in the wrong hole, you don't have to worry since the microphone end filter are seated above the holes so it's like an l shape and the simujector two won't reach them to cause any damage there's one millimeter wave five g on ten on the top right and one on the bottom left of the phone the top right one is held down with some adhesive and the bottom left is held on with two filled screws also some variance of this phone for different regions might not come with these antennas and that doesn't mean that the phone doesn't have five g these antennas are just for those carriers which use the ultra white band five g if you need to replace the flex table, power, button or volume keys there's a plastic and metal bracket in the frame, you'd have to pull that bracket out of the frame lifting it up and pulling it out, and that will give you access to removing the physical keys or replacing the flex table all right so to pry the screen off we need to apply heat to the front of the foam, so we can loosen up that he's underneath and then we're going to use a suction cup tool to help gain leverage between the screen and the frame and then we're going to use a plastic pry tool to pry the screen off here's a better look at the screen the fingerprint sensor is located here and there's a cut out on the screen on the top for the proximity sensor, so i just put the flex cable over here to give an example, so if the screen flex cables over here and you pry your screen off from the front without disassembling the back when you're applying your new screen you're gonna have to line the connector with the flex cable over here since there isn't much movement with the flex cable, so you just get your screen and line up correctly then have to press down to make sure it connects aside from that underneath the screen on the frame to some copper tape as was a large lay of graphite to help transfer heat for the repairability score i give this one to seven point five out of ten now it's time to put the phone back together once everything's back in place apply a new adhesive and a replayer back plate tip over the phone power it on and you're done it looks like the display got damaged when i was prying it off i hope you enjoyed the video and i'll see you in the next one。

好看一下,这个包裹又是哪里进来的啊?湖南省衡阳市。这个是本省的,这是本省的粉丝进来的。看看什么是是什么东西啊。又拆个盲盒,这每天盲盒很多的,不是每一个都能拍作品,因为没有时间去。每一个都拍太多了, 没有时间拍,哎,又是一个耳机。 哎呦,这个纸条 隐藏的好好深啊。这个耳麦坏了什么?生气时 还把耳麦拔掉了,这打游戏打输了吗?没事,你拔拔耳麦拔麦克风吧。哎呦我去,你看来这粉丝绝对是打游戏被别人 要不就是吃鸡,可能没吃到鸡被别人给秒了。估计是,估计是被别人爆头了,哈哈哈哈。哦,还有一种可能,有可能是有可能是这个麦克风坏了,他这个他说话可能队友听不到,估计得把麦克风给拔了。哈哈哈。去,等下整块换整个换。 哦对,这不就断了吗?这里面这钢。你真猛,这里面这个都是钢的。嗯, 这里面这个钢钢条都被你给拔断了。我去啊,开干吧 这个。我去,你,你这是连根拔起的,这里面线都不见了。哎呦我去,你是真够猛的,这里面线都断了, 这里面用胶拔断了。 邀请完了,邀请完了还要把他把他切开 切,他要换一个刀头了。这个手机电脑 pcb 除胶切割仪。除了除胶好用,他切割也好用。切割有专门切割的刀大孔。这么大孔,一个刀开孔,开动开动,可以开动的刀。 有人说耳机飞线什么必须要重新开空,没这东西就干不了活啊。 简单吧,没有他这东西就取不出来。拿麦克风去 拿个全新麦克风, 这部分操作就又涉及到核心技术了,要暂停一下。哈哈哈,搞好再做展示,不做免费教学,谢谢。哈哈哈。哎,搞定了 看不出来,修过吧,没有一点痕迹。祝你今晚吃鸡。哈哈哈。不要再扯麦克风了,我换这个麦克风比原来这个还好,这个这个还这个比原来的好很多。现在测试一下, 测试一下。暂停, 把音乐暂停,测试一下麦克风功能啊。测试开始。 喂喂喂喂喂喂喂喂,一二三四五六七七六五四三二一喂喂喂喂喂好,测试,测试完毕看一下哦。要把这个要把这个耳耳耳机给它拔掉,不拔掉你们听不清楚。 好,停一下。喂喂喂喂,一二三四五六七七六五四三二一。喂喂喂喂喂, 好好搞定,这就测试完毕,声音正常,麦克风正常。 ok, 搞定搞定,收工。
