让我困在城市里。
粉丝4.4万获赞23.4万


轻轻卸下透明机盖, 对准中心安装盘片转动,盘片露出金色传动轴,轻轻撕下胶带, 挂皮带的时候注意皮带不要扭曲啊,轻轻的挂在 金色传斗中的槽内, 注意另一侧不要挂皮带。 然后解开唱币, 取下唱真的保护壳, 放上粘垫,手动顺时针转十圈,一定要缓缓的转动, 然后安上透明机盖,安装结束, 一个是音箱,一个是空放,然后另一端连接音箱的左右声道,红色连二,白色连 l, 插上电源试配器, 然后选择唱片对应的尺寸,十二或者七英寸,根据唱片选择转速三十三和四十五, 按下 star 的启动,唱机唱真自动抬起,开始工作,音乐缓缓的流出。

the lp sixty x usb is a fully automatic belt drive turntable equipped with a usb output for sending a digital signal to a mac or pc computer convert your vinyl records to digital audio files using readily available recording software before you can begin using your turntable it needs to be set up carefully unpack the turntable and make certain that you have all of the parts and accessories begin by installing the platter and drive belt carefully place the platter on the spindle and make certain it is fully seated rotate the platter by hand until the rectangular opening with the red ribbon exposes the brass motor pulley the brass pulley is located in the upper left hand corner of the turntable opposite the tone arm do not confuse the motor pulley with the white plastic post located near the tone arm while holding the platter steady remove the tape securing the red ribbon the red ribbon is used to install the drive belt onto the motor pulley holding both ends of the ribbon carefully place the belt over the motor pulley once the belt is seated in the pulley's groove carefully remove the ribbon and verify that the belt is not twisted next place the turntable felt mat on the platter with the tone arm still fastened to its rest slowly rotate the platter by hand ten times in a clockwise direction to make certain the automatic mechanism is fully cycled next remove the twist ties securing the tone arm and discard the die while holding the tone arm remove the plastic stylus guard by slowly pulling it forward being careful not to damage the stylus for best operation the turntable should be placed on a solid level surface with the turntable assembled the power and audio connections can be made connect the power adapter cable to the turntable and plug the adapter into a convenient ac outlet the turntables usb output allows it to connect digitally to mac or pc computers without the need four special drivers compatible with a wide range of third party recording packages the usb connection allows you to record from the turntable to the computer simply connect the usb cable from the turntable to an open usb port on the computer the lp sixtyx usb also provides an analog audio output this output is compatible with traditional phono inputs on amplifiers and receivers or by using the turntables built in magnetic phono preamp will work with ogs or line level inputs on powered speakers, amplifiers and other devices if your audio device has its own riaa magnetic phono preamp simply set the selector switch on the rear of the turntable to phono bypassing the turntables internal preamp if you are connecting to an augs type line level input powered speakers, soundbars or other devices place the selector switch in the line position to use the turntable's internal phono preamp connect audio devices such as powered speakers directly to the turntables ath inch mini jack or use the included ath inch to rca cable to connect the turntable to rca type phone or auxiliary inputs found on amplifiers and receivers the turntable includes a plastic dust cover to protect the turntable when not in use four best results remove or close the dust cover when playing records for more information visit us on the web at w w w dot audio dash technica dot com。

好的,我们今天给大家分享一下铁三角黑胶唱机如何安装, 我们首先认识一下这里面这个金色的,这是传动轴,这边是个固定的啊,这边是个固定的,所以我们安装皮带的时候一定要安在这个轴上才可以啊, 啊,这样我们再看一下转盘,我们的转盘拿到以后啊,底部这一圈就是他的传送带, 传送带啊,即使你安装的过程中传送带掉了也没关系,就把它套上去就 ok 了。这边呢有到一个孔啊,这个孔呢是有一个胶布 粘着的啊,我们要安装的时候一定要把这个孔对准这个金色的这个位置啊, 对金色的位置,然后把这个胶条撕掉,把头轻轻的挂在这个皮带上,挂在这个传动轴上,这个时候记得啊,一定不要扭曲 啊,这样的话我们的皮带就挂好了啊,大家可以看一下,嗯,装好了以后我们要把它啊转几圈看一看啊。 好的,我们再把这个胶垫放在上面啊,保证我们的唱片更平整更平稳,这样话唱攀就 安装好了,我们收到唱机的时候呢,这个唱真币是固定的啊,我们记得把这个绳拿掉啊,把这个绳拿掉, 我们收到以后啊,这个唱针头有一个保护壳,这个白色的塑料壳啊,不是上边这个带标志的这个壳啊,这下边这个壳,这个壳的水平方向就可以拿出来啊, 一手按住长针臂好就可以摘下来,这时候长针就是可以处于播放的状态了。 这款唱机和以往唱机不一样的地方是他有一个亚克力的防尘机盖,这个盖呢 啊,我们是可以这样安装上去的,非常简洁啊,安装上去也可以这样打开,也就是放盘的时候无需把它摘下来 啊,这个大家注意到了吗?这个好多朋友都不知道,这是干嘛用的啊?这是可以取下来的啊,取下来放在这个位置, 这是干什么用呢?因为有的唱片中间是一个有孔,这个是一个适配器,也就是如果你买到的唱片他中间是有圆孔的话,用这个可以去适配啊,这是一个小小的一个设计, 这个唱机呢可以播放两种尺寸啊,这边是个七英寸,这边是个十二英寸,就是可以通过啊这个 旋钮来控制你的播放尺寸,然后这边的按键呢,简单了啊,这个是开始 start, 这个是 stop, 这个是干啥的?也有人问啊,这是一个手动抬起唱臂,如果我们为 来更换唱真的话,可以用它啊,可以让它抬起,可以让它放下,我们没有接电啊,这一边是一个转速, 这个唱机呢还可以播放两种转速的唱片。开关在这里啊,有一个是三十三转的,有一个是四十五转的,调节方法就是按下这个按开关,还有两种状态按下或者是弹出。 我们现在看一下这一款唱机的背面啊,背面这边是个电源线啊,这个不用讲啊,这边是他的声音输出插孔, 这个也不用讲,我们也都有那个配备到的音频线,那么这个开关大家需要关注,他有两个位置, 一个是 line, 一个是 phone nophone, no 是指的我们家里的音响系统,带功放的音响系统,你要播到这个 phone 的位置,如果你直接用啊,电脑音箱啊,或者一个普通的有缘音箱去 搬到这个烂开关,就可以用它来欣赏唱片的音乐了。取一个唱片放在黑胶唱机上,然后按下 start。

这个发光唱盘的话,它是专门跟七零叉定制的,但这个唱盘它用起来我们音质是没有什么影响的,它目前我们自己发现它用在三叉上面也没有问题,但是它会有缝隙,如果你不介意它中间有缝隙的话,那么其实这个发光唱盘还是可以用的。 按这个唱盘了之后的话呢?呃,这个地方的话需要拿我们给您的那个圆圆胶给它贴紧一点,贴紧一点,不然这个线它飘起来的话会会打到我们的转盘。

铁三角、黑胶长吉 atlp 六零叉拿到手以后第一件事要安装他的铝制转盘,先把转盘放进去,然后找到 这个铜色的转轴,然后把皮带轻轻的解一下啊,记得挂的时候一定要是挂正了,不要扭曲。好,挂上去以后 我们平稳的转两圈啊,感受一下,如果旋转平稳就是挂对了。

第三部分,唱击的连接和使用操作,然后选择输出模式,蓝或者后脑一个是音箱,一个是功放,然后另一端连接音箱的左右声道, 红色练 r, 白色练 l, 插上电源识别器, 然后选择唱片对应的尺寸,十二或者七英寸, 根据唱片选择转速三十三或四十五, 按下 spa 体重,超级抗震,自动抬起 开始工作,音乐缓缓的。

the atlp twelve forty usb xp is a professional quality turntable designed for dj applications as well as general listening it includes a lightweight headshell with pre installed atxp five cartridge before the turntable can be used it needs to be set up carefully unpack the turntable and verify that you have all of the parts and accessories position the turntable chassis on a sturdy surface carefully place the platter on the spindle and make certain it is fully seated place the slip mat on the platter next assemble the tone arm remove the twist tie and temporarily secure the tone arm to it rest with the locking clamp attach the head shell with atxp five cartridge by inserting it into the tone arm socket while holding the head shell in position rotate the head shell locking ring counter clockwise as the ring rotates it pulls the head shell into its seated position tighten carefully install the counterweight making certain the black stylus force gauge dial is oriented toward the front as you rotate the counterweight it will thread onto the tone arm now we will balance the tone arm set the tracking force and adjust the anti skate for the atxp five cartridge this important process allows the cartridge to track properly and failure to do so can cause the stylus to wear prematurely and possibly damage your records first set the anti skate at just investment knob to zero carefully remove the stylus protective cover by sliding it straightforward off the front of the cartridge exposing the stylus while gently holding the head shell to stabilize the tone arm carefully release the locking clamp at this point the tone arm is unbalanced and can easily swing be careful not to drag the stylus across the platter while gently holding the head shell rotate the counterweight until the tone arm is horizontally balanced it should hover freely just above the platter and not touch the platter surface once the tone arm is balanced without touching the counterweight carefully move the tone arm to its rest and secure it with the locking clamp now set the stylus tracking force the atxp five dj cartridge has a tracking force range between two and four grams with three grams being standard depending on your application you may desire to track lighter or heavier than the standard three grams locate the black stylus force gauge dial marked with numbers and lines indicating different tracking forces the dial can rotate independently of the counterweight without turning the counterweight carefully rotate the stylus force gauge dial until the zero on the dial lines up with a central line marked on the top of the tone arm now set the tracking force by rotating the entire counterweight assembly in a counterclockwise direction as you rotate the counterweight note that the gauge dial rotates with it continue turning the counterweight until the three value on the gauge dial lines up with the center line mark on the tone arm you now have set the standard tracking force for the atxp five cartridge if you ever change out the cartridge and head shell you will need to rebalance the tone arm and set the tracking force to the value required by the new cartridge the atlp twelve forty usb xp has an anti skate force adjustment this small outward force can be applied to the tone arm to compensate for the natural skating force that pulls the tone arm toward the center of the record four best performance during normal turntable operation set the anti skate adjustment knob to the same value as the cartridge tracking force the turntable includes a stylus queuing light it illuminates the record surface to assist in finding the groove in a low light situation if needed plug the queu light into the receptacle on the chass and aim, it as desired when properly set up the tone arm is parallel to the record surface if you are playing thicker records adjust the tone arm height loosen the tone arm anchor lever and using the height adjustment dial raise or lower the tone arm as needed after the adjustments are complete tighten the tone arm anchor level for best performance the turntable should be level using a small bubble level adjust the turntables feet as needed to make certain it is level with the turntable assembled and leveled the power and audio connections can be made first connect the ac power cable to the turntable and plug it into a convenient ac outlet the atlp twelve forty usb xp provides a traditional phono output along with a built in magnetic phono preamp providing an r i aa equalized line level output this makes it compatible with traditional phono inputs on some dj mixers and amplifiers along with ogs or line level inputs on powered speakers, amplifiers and other types of mixers if your audio device has its own riaa magnetic phono preamp simply set the phono line selector switch to phono by passing the turntables internal preamp if you are connecting to an augs type line level input or powered speakers place the selector switch in the line position to use the turntables internal funo preamp if your audio device has a separate ground terminal connect the spade lug on the dual rca cable to the grounding lug on your audio component to help minimize home the turntables also equipped with a usb output allowing it to connect to mac and pc computers without the need for special drivers compatible with a wide range of third party recording packages the usb connection allows you to record from the turntable to the computer simply connect the usb cable from the turntable to an open usb port on the computer the turntable's dust cover is designed to protect the turntable when not in use and should remain off when records are playing for more information visit us on the web at w w w dot audio dash technica dot com。

第三部分,唱击的连接和使用操作,然后选择输出模式,蓝或者后脑一个是音箱,一个是功放,然后另一端连接音箱的左右声道, 红色练 r, 白色练 l, 插上电源识别器, 然后选择唱片对应的尺寸,十二或者七英寸, 根据唱片选择转速三十三或四十五, 按下 spa 体重,超级抗震,自动抬起 开始工作,音乐缓缓的。

大家好,我是修黑胶唱机的将总,今天来讲一讲铁三角这两款入门机的区别。一款是 atlp 六零,一款是 atlp 七零 x, 其实它升级的应该是 s p 六零 x 版,它这个 x 版和没有 x 版的区别不大, 就是 lp 六零的 x 版和非 x 版区别不大,主要的就是外形的区别,外形呢,那个前沿前端呢?看起来薄一些啊。剩下的就是那个机器改成了外置电源,这个机器是内置电源, 那个改成了外置电源,然后其他的区别不是很大。这款机器呢,它有机身自带音频线, 带的是这种双莲花头,这个版本也有三点五叉口的版本,其实我个人更喜欢叉口的版本,机身呢,就是没有线, 电源也是外置插拔的,然后音频接口也是插拔的,这样我感觉方便舒服一些。其他的机芯的结构,唱臂、唱真,嗯,等等。 就这个六零和六零 x 是 没有什么本质区别的,也就这两款机器其实音质是没有任何区别的,主要就是外形风格不一样,一个呢就是简约一点,方方正正。另外一个呢就是边缘薄一些,更流线一些。 然后这两款机器呢,包括 x 和这款七零,他们区别就会很大,这款机器就是近两年铁三角用来代替六零的一款机器。 嗯,首先说外观吧,它的外观呢,尺寸方面比六零要宽了一些, 六人的话,他前后加起来差不多是方形,差不多是方形,但是前后也宽一点左右窄一点,而这个机器呢就变成了,嗯,长方形, 他更宽一些,然后这里布局呢,没有那么急促。然后另外呢,然后就是他这个机身是双层机身,这里 这个银色的部分,还有这个白色的部分,其实它是两层,两层壳体堆积在一起的,它这个做做工呢就更繁琐一些, 它要的应该是为了这种配色,做工也要更繁琐一些, 用料的话是差不多。嗯,机芯结构也是一样的。 而我觉得一个挺好的提升就是它出的是外置电源,它的接口改成了,嗯,双莲花头的接口是可以插拔的。另外一点,最最重要的就是它只它有一个接地。 嗯,像这种机器呢,他都是内置唱放,你也可以选择接外置唱放,就是接这种外置唱放。接外置唱放的时候有一个很重要的一点就是最好去接地线,接完地线以后呢, 他的声音就是噪音就没有那么大了。如果你用内置唱放可以不接地线,但是用外置唱放的时候,不接地线很有可能会有很大的噪音。像这样的机器的话,当你用外置唱放的时候,他没有地线。 嗯,这种机器呢,它增加了一个地线接口,然后我们可以选择外置唱放。外置唱放呢?嗯,你像这种不是太贵的唱放,相对来说也能提升整体的音质。 嗯,另外的区别是唱臂,唱臂的话,它这个唱臂的结构轴部 唱臂的结构更偏向于呃专业一些的唱机的唱放,但还未达到,毕竟他的定位也是属于入门机。但是他这个台臂键 改了,台臂键是改成这种杆式的手动杆式,这个手感不得不说特别好,就是这种的按键式的台臂其实也没毛病, 也可以,其实,但是呢,这个手感我个人觉得是这种偏向于高端机器的机器呢,都是这种手动抬杆式的,这个做的非常丝滑, 这个我觉得是很好的提升,整个唱臂也算提升了,最最最重要的它的音质也提升了。音质提升在哪呢?它的唱头变了,像这种机器用的全部都是铁三角三六零零的唱真 x 版,也是是铁三角里面最最入门的一款唱真,虽然音质也不俗,但这款机器呢,它的唱真提升升级了,它的唱真 是九五系列的唱真,九五系列蓝真,它这个唱真,呃,和之前铁三角的像, 嗯, l p 就 幺二零系列的唱真标配,已经是达到同样的唱真了。那个机器新机器应该是在两千多, 两千多这个机器的市场价现在应该是不足两千,所以它这个唱真换了以后对音质的提升是非常大的, 我觉得对音质提升最大的是唱真,唱放音箱,这三个点非常重要。 然后这个机器他就把唱真也给换了,这点提升特别好。总体来说,我觉得这款机器作为铁三角新款的入门机,比较的比较的不错,提升也比较明显, 这款机器现在应该都停产了,嗯, 基本也就是这些吧。那这期就先到这里, 有什么问题呢可以在留言里问我。这期就到这里,下期再见。