粉丝3.5万获赞35.3万


大家觉得七九零零 x e x 超白金能装进小型机箱吗? 正确做法是揭开后盖,取下底下风扇架,有请自身放进去啊,一声搞定!请欣赏正片 暂停一下,你们觉得这款装得下不?

中高端的显卡偏重会导致显卡倾斜,所以就不得不要用到显卡支架金属结构安装方便,底部自带磁吸固定。显卡与支架接触的部分都有硅胶保护设计,所以就别再用根筷子当显卡支架了。

近期买三零七零魔龙的小伙伴很多,那在发货的时候,我们的显卡支架是没有给大家安装的,因为显卡支架如果说安装在底下的话,发货途中他颠簸可能会有前后位移的状况,会影响到显卡,所以今天我们出一些视频,专门给大家讲一下如何安装显卡支架。 安装显卡支架其实很简单,您只需要准备一样工具,那就是气质,剩下的有手就行。首先这次给大家推荐了两个配置的话,选用的机箱都是九州封神的魔方三幺零,这个机箱呢,它是自带显卡支架的,所以不需要去安装啊。显卡原本的支架, 那如果是有些小伙伴更换了其他机箱的,那下面注意一下,其他支架就在盒子里面。我们先打开盒子, 首先我们打开机箱前盖 以后,我们看到后面这个位置会有一个披萨衣拓展卡的一个曹魏背板,那我们先把这个盖子给打开, 拿下来以后所有的机箱都一样,你能看到这个螺丝,每个披萨一插槽的呃孔位螺丝都是在上面的, 那接下来我们就要把呃显卡支架两体才一到他应有的位置,那么大概固定在这个位置以后,我们就需要把这上面的一二三四个螺丝下来,然后把这个显卡支架安装安装上去啊,直接卡住就是把螺丝下来,把这个显卡顶进去就 ok 了。 那接下来我们就把机箱放倒,然后因为竖插的话他可能不太好上,那我们轻轻的把这些槽位轻轻再对上去,哎,把螺丝下来以后 轻轻的把,先看支架对齐啊,先看之下这边,这边有一个软的橡皮啊,顶住,先看就 ok 了,然后我们把螺丝上起来, 现在呢?我们这个情感支架就已经上好,然后最后再把这个盖板盖上去就 ok 了,学会了吗?

首先我们将显卡支架放置显卡右侧下方, 我们调节滑轮,让滑轮顶到显卡底部,拧紧螺丝, 找到电脑的五伏三针接口, 将显卡支架的母头线接入三针接口,这样就大功告成了。我们来开机看看效果吧, 是不是很简单,赶紧拿上宝贝去安装吧!

这几天有很多小伙伴反映自己家的显卡支架安装的问题,那我们今天仔细来说一说,像这个大版的话,一般他的这两个螺丝孔位与显卡这个插槽呢,是有一段距离的,但是像这种小版的话,他显卡插槽与螺丝孔的话是处于一个平行位置, 那像这种的情况下,正常安装安装显卡支架是装不了的。那像这种情况的话呢,我们是需要把这个支架给他反个方向啊,就像这个样子,然后螺丝给他拧上, 拧上去之后呢,我们需要用到扎带,把两个支架组件给扎在一起,这样的话就可以。呃,使用这个支架啊,现在我们是 在做一个演示,螺丝暂时没上,但是大概位置在这个这里啊,然后我们把另一边的指甲逐渐拿螺丝拧上去,拧上去完了之后大概就是那个脚上 把扎带给他扎起来,稳定性的话也会比正常那种支撑式的支架会好很多啊,然后装好的效果大概就是类似这个样子,呃,也可以自己装的话可以装的更好看一点,我这里也就做个演示看一看啊,希望可以帮到大家。

不会吧,都二零二二了,还在用根筷子当显卡指甲夹?烟纹肉姐显卡指甲车 又来了,一套夜明脖子钱就能搞定!由于三菱系列中高端显卡偏长偏重,导致显卡倾斜,会夹住主板的 pcb 板和机箱的负担。这款显卡支架之前开过车,大家的反省还是很不错的嘛, 便宜又好使,干净又卫生。整体啊,是一个金属结构,这个地方最高可调制到十二厘米,就是显卡底部聚电源仓不超过十二厘米的都 不能用。固定显卡的这块距离啊,最高可调节至六点五厘米,就是只要您的显卡厚度不超过六点五厘米的都能用。显卡与支架接触的部分呢,都有橡胶保护,放心吧,不用刮花米。漂亮的显卡底部啊,是 vhb 胶固定 vh b 胶,好处啊,就是移除后接触部分不会留有胶痕。显卡支持 mat 叉和 atx 机箱,但是注意啊,如果你的机箱没有电源舱, 可不能用。我的显卡是索泰的次旗舰天启三零六零肽三风扇,长三十一毫米,厚六十毫米,宽一百毫米,装上显卡支架后,平衡感提升明显。当然了,显卡指甲有十几块钱的,有几十块钱的,有几百块钱的, 甚至你拿根筷子都能解决。这东西啊,就是封建有机人均选择下方,小黄车出发!

收到电脑不会安装显卡怎么办?今天呢给大家带来一期非常详细的显卡安装教程,我们就用最近比较火爆的这个弹药过气箱给大家做个示范。咱们弹药过气箱呢,后面有一个按钮,直接按下弹开,然后把侧板取走 来。首先咱们先把机箱平卡,咱们装显卡的时候,这边架子两颗螺丝先把它下下来,咱们这边会预留三颗这个固定显卡的螺丝,咱们先把它取下来 来。咱们装的时候,有时候显卡的角大家注意一下,不要插到机箱外面,机箱的侧板和这边主板中间有个缝,大家注意一定要把这个显卡的角插到缝里面,不要插到机箱外面了。取出显卡之后,咱们 先拔掉金手指上面的一个防尘盖,怎么装的时候呢?显卡放下去先不要插啊,先对一下这个角,看下有没有插到外面好,这样就没有了。 咱们插显卡之前呢,先把显卡的金手指和显卡插槽先对好,位置对好之后,然后再把它按下去。 显卡插好之后,咱们接下来就是固定显卡螺丝啊, 显卡的这边的挡板也把它放回去,然后用这个固定好。 机箱内部我们会把显卡供电线预留在里面啊,这边四零系列显卡十六频的供电线 两边有卡扣,方向不一样,大家插之前可以先对一下啊,然后对好之后直接把它插紧就好了,有个小卡扣,然后插紧的话会有咔嚓一声,如果有听到的话,那就代表这个功能线已经接好了, 现在咱们显卡已经安装完毕了啊,然后显示器的连接线一定要接到独显的接口上,显示器连接线要接到咱们的显卡的接口上,这边上面有防尘盖啊,选择其中一个把它接好就可以了。这个是咱们丹药科技箱自带的显卡支架, 咱们安装的时候可以松动这个螺丝调节高度,然后确定好高度之后再把它拧紧,然后直接垫在显卡下面支撑就可以了。这是咱们自家安装好的一个效果啊,因为像这个架子的 他底部有一个非常厚的磁铁,吸力非常强啊,也不用担心他会晃动什么的。到这一步显卡已经安装完毕了,咱们把侧板盖上啊,就可以通电玩游戏了。不会装显卡的兄弟们,你们学会了吗?

没有显卡支架,显卡三个月真的会弯,特别是三零系、四零系显卡,一定要选择合适的显卡支架,不然等弯了就来不及后悔了。 显卡支架有两种类型,托盘类和支撑杆类,分别支持不同类型的显卡。托盘类支架适合饮食的名人堂或者是七彩虹的 ad 中表面凹凸不平的显卡。只有托盘类的支架才能找到着力点,同时它的支撑力也够大,而支撑架容易在凹凸不平的表面滑倒,如果你的运气不好,甚至可能打到风扇。 支撑杆只适合表面平整的显卡,或者你的机箱太小时,托盘内的支架塞不下,那你就有支撑杆。还有些机箱构造特殊,比如异形机箱,小体积的支撑杆能更容易操作,更容易找角度去支撑。 市面上的显卡只有金手指和背板机箱连接处两点受力,这种受力结构加上三联系四联系,动则四五斤的重量,这个角是必弯的,所以显卡支架要架在这个角的位置。显卡弯曲的时间长了,挤到 pcie 板了,那就真的是坏了。如 如果你懒得买的话,可以用眼药水瓶或者是一次性筷子,反正就是一定要把这个脚给支撑住,防止它坏掉。如果有配置问题或者装剂疑惑,可以关注我后给我留言,我会一个一个回的,也可以去我的橱窗看一下我搭配好的配置,我们下期再见!

好,大家好,今天给大家介绍一下这两款显卡支架,这个叫做小胖子。呃,这个是长,现在这样子是五厘米,就是五厘米,他最高的话是可以加高到八厘米,八厘米他这个锁黄把它锁住他就会掉下来了。 啊,这样子的话就是八厘米,八厘米七, 这里还有一公啊,你们那里没打起来了?八厘米啊,八厘米的话,对于那种矮一点的就显卡支架这里空间不够的,用这种八厘米到五厘米的,就用这款,比较油耗, 这个也是非常大的,这直径我看你建议多少?直径是三点四到差不多三点五,对有误差,然后下面是 有磁铁磁吸,然后外面是贴了一个硅片,这样子防滑大磁铁磁性非常好, 顶上呢也是用了一个硅胶贴,这样子就不会碰到声卡上面电子元件或者是外壳壳刻花之类的,而且也是非常, 那你的气量就 ok 的了。这个比较高,所以这样子展示一下啊。下面来说这一款,这一款呢是八厘米到十三厘米的,他现在默认是八厘米,然后最高的话是十三厘米, 八厘米,八厘米, 啊啊 啊,这样子的话就是三厘米的。嗯,任何机枪都可以使用的,基本上 他这也是一样,他用的大磁铁,然后外面贴了个硅胶防滑,顶上也是硅胶,这个磁性你看这样子都不会掉的,那磁性挺好,不会防滑,然后这里再高的显卡十三厘米都可以顶上头, 他没有磁性,他不会。不,不怕他晃动你就会跑, 特别舒服的啊,这个 ok 啊,今天把它给顶上去, 这样子啊,看他手旁有手术的。 好,我现在就完成了。

哈喽,大家好,我是长平哈,今天我们来开一个这个东西,这个是如果有用过的朋友应该知道这个叫显卡支架啊,这个是 id 七彩虹的,来推进一下。 ok, 然后这里边有一个质量保证卡,也就是我们说的保修卡啊,这个没啥看,放到一边,这里有两个夹子,是用来夹在显卡上的,这两个夹子上面有海绵在这里啊,不会伤到显卡。 然后这里边还有一条线,这条线的话是一个五福三针的,也就是说这个这个支架是支持神光同步的,啥情况哦,好 紧,证明他是新的啊,这个就这样子,我们就有延长线,然后直接插到主板上啊,把这两个那,那么你的显卡很重的时候,这个东西就起到作用了, 如果有兴趣的朋友可以了解一下这款产品。哇,一会我让技术装上我的电脑上,给大家展示一下实际的效果, 这是已经装好的一个效果,支持神光同步啊。完了,就是 i game 的,他下面是有磁吸的, 但是我一直没理解上面这个是干啥的,下面我知道防止跌下去,不过整体搭配出来还是挺漂亮的。 ok, 有兴趣的朋友了解一下这个小东西。

显卡怎么拆?这是一个显卡支架,可以直接拿下来吸铁石,这下面是吸铁石,吸到这了,装好以后顶到这个位置,注意不要碰到下面的风扇就行, 从这压着压着这个卡扣拔线,你回去以后把这个照着这个眼插好,一定要对准以后再插,插好这个卡扣挂上就可以了, 后面有两个螺丝,你安装的时候系好,这后面这两个螺丝一定 要装好,这样的螺丝 你找个小小那透明塑料袋来,我把这装上。显卡 上面有一个按钮,一按这是这是取钱卡时候用的啊,一按按下去以后将它拔出就行,千万不要滑到主板, 这有这铁片,装的时候千万不要滑到主板,这有一个缝隙,插到这个缝隙里就可以了,对准以后装好卡通 一声听到了吧,这就装到位了,这是装好了,取的时候按这个 所有操作,一定确保断电,然后不要滑到主板,千万不要滑到主板。

火神显卡支架怎么安装呢?非常简单,显卡装好后,从配件盒里拿出显卡支架,配件一个底座,三个支撑柱,一个支撑杆,两个一样的快拧和一个不一样的快拧,这个快拧呢是拧在这个支撑柱上面的啊,一个美观的作用啊, 给他拧上,然后呢拿一根支撑柱拧在底座上面, 再把支撑杆呢给他套上,首先把这个卡扣打开,然后套上,套上这个卡扣先不要扣啊, 然后根据自己机箱的大小和这个显卡安装的高度啊,决定用几根这个支撑柱啊,一根,两根,三根都可以啊,这里呢用两根, 然后呢怎么固定显卡呢?可以看到咱们显卡尾部呢,它是有两个螺丝孔的啊,这两个螺丝孔是对应咱们显卡支架的两个孔的, 这个时候就要到咱们两个一样的快拧,哎,孔,对好,快拧,拧上去哎,两个都拧上去,然后呢调节一下咱这个呃支撑杆的一个高度,然后把 把这个卡扣给他扣上,这就装好了啊,非常的简单。

greetings and welcome to another how to video from ike my name is metitz and today i'll show you everything you need to know about water cooling the amd ray day on rx7900 xtx graphics card with our water block from the gpu disassembly to the step by step installation of the rx7900 xtx water block, and if you're looking for more similar content and information about cool new products subscribe to our youtube channel and newsletter and follow us on social media also be sure to visit our web shop to find just the right liquid cooling gear for your build this beauty right here is the radio on arix 7900 xtx water block not only does it look stunning, but it also provides high performance cooling for the graphics compute die, the voltage regulation module, voltage controllers, vrm and the mcds on this fantastic gpu compared to other vector to water blocks this cooling engine has been rotated by 90 degrees so the fins are perpendicular to the die for optimal delta the coolant flows over the graphics core die first and the memory cash die after so all the mcds get the same temperature coolant the water block is also available in the acetyle version, and we also have something very special for you this is the ek quantum vector to r87900 xtx amd right there on addition a limited quantity's water block made to celebrate the launch of the latest gpu based on the amd rdna3 architecture both water blocks fit reference pcb designs of the radio rx 7900 xtx gpus also available are the versions that fit the ace stuff and power color devil for precise compatibility information about these water blocks we recommend you refer to the ek cooling configurator this installation also applies to the right down addition water block now let's dig in first, we'll unplug these two cables on the bottom side try not to pull on the cables themselves, but use a small flat screwdriver to gently wiggle each side of the plug believe it or not this was the hardest part of the whole process now let's unscrew the back plate of the gpu by removing these five screws and there we go now before we get the pcb out we should remove this three screws on the io bracket so far so good and quite easy we will now remove all 15 screws on the pcb while leaving the last four on the clamp to be removed last luckily all 15 screws are the same so it will be easy to assemble the cooler back together now for the last four screws on the clamp we'll first unscrew them halfway then we'll slowly unscrew one of them and while doing that we should hold the clamp so the screw doesn't get lost due to tension now we can safely remove the last three and we're almost there, we'll now wiggle and leave the pcb slowly alternating the sides and there we go that wasn't too difficult we recommend assembling the cooler back and safely storing it again if you ever need it what's left is cleaning up the dive for the new thermal paste and with the gpu ready we are good to go with blocking this bad boy with some ek goodness step one we should first unscrew the six screws on the back plate with our out removing them your block will arrive with a dami cardboard pcb in between the back plate and the block so be sure to remove it once you've removed the back plate make sure you scan the qr code to see the installation menu step two the gpu water block comes with thermal pads that have to be cut into smaller pieces to cover all the necessary components such as the vrm, the vrm and the die, so let's just cut thermal pads accordingly step 3 once cut to size thermal pads should be placed on the pcb as shown in the installation manual and do not forget to pill both sides of the thermal pads the end result should look something like this step four apply and close thermal paste on the gpu die and remember do it in a cross pattern step five first pick up the box and put the block on top of it now carefully position the pcb onto the water block with pre installed standoffs during this process align the mounting holes of the pcb with the holes on the water block step 6 from the mounting kit use the 10 mounting screws and pvc washers to tighten the pcb onto the block the mounting screws are the shorter screws in the package tighten the screws evenly using the filling head screwdriver to prevent gpu damage we recommend tightening the screws around the gpu core first and then continuing outward tighten the screws around the gpu die in a cross pattern go halfway first align the whole pcb and then tighten them step 7 with the water block attached a few more thermal pads need to be cut into smaller pieces to put them on the back plate step 8 fill the thermal pads and apply them to the back plate as shown in the installation manual the anti should look something like this step 9 the final step is to position the back plate including the screws and standoffs onto the gpu's pcb once all the hose are aligned you can tighten the screws evenly half a turn here half a turn here two turns here three turns here and there we go the ek quantum vector 2rx 7900 xdx water block is now ready to leave the performance of this gpu to new heights that's it for today i hope we managed to bring the 7900 xtx water block installation process closer to you and show how easy it is feel free to contact our customer support anytime you have questions or need help with our products like comment, share and subscribe if you dig this video video and be sure to dig through our youtube channel for more useful water cooling videos until next time stay cool。

市面上琳琅满目的显卡指甲,哪一款才是你的?才第一个友情出战呢,就是我们传说中的筷子。筷子指甲的优点啊,就是看着比较简洁,携带起来比较方便,安装起来也比较简单,只需要量好了。吉祥电源仓跟显卡的距离 往上面一放,他底部是在慈禧的啊,可以立得住,然后长,你看,哎,拧就长长长长长长长长长长,变短就往下拧,短短短短短短短短短短短。 看见吗?比较方便。但是呢,缺点是什么?缺点是这个分为三个规格,小号、中号、大号。我手里这个啊,是大号哎,没错,这是大号。 显卡与电源仓距离二十到五十毫米,适用于迷你款。显卡与电源仓距离四十九到八十毫米,适用于中款,而且有黑 两种颜色。显卡与电源仓距离七十四到一百二十毫米,适用于 plus。 长款也同样有两种颜色,因为相同的一款迹象,比如说爱国者 a l 五,放一个小的显卡, 用大的就 ok, 放高端限号三十七,比较厚的显卡,那就要买小号或者中号。第二款支架就是好多喜欢光污染小哥哥的福利 带灯的显卡支架,他呢,也可以说是第一款的升级版,带一个 airgb 的灯条,喜欢光污染的小哥哥可以考虑一下。 安装方式跟第一款一样,也是拧起来长长短短的,可以随意调节,优点就是让你的整体迹象看起来更散哎,闪下我的钛合金狗眼。那缺点呢,就是它的接口啊,是五福三针的这种 airgb 的接口,所以你的主板必须要有五 三针接口,这样才可以哦,如果主板没有五福三针接口,也可以选择带控制器的 airjb 显卡支架哦。第三种也就是我平常来给大家介绍这一款,优点就是可以根据电源舱和显卡距离还有显卡的厚度啊,都可以随意调节, 基本上除了包豪斯那种没有电源仓的迹象都能用。缺点呢,就是因为它的方式是可以加着你的显卡, 所以这个地方经常一不小心会压着我们显卡一部分风扇装上以后就有那种嘎嘎嘎嘎嘎吧声音,所以装的时候一定要调好角度。显卡指甲这个东西,便宜的几块钱,贵的几百块钱的都有,根据自己的需求风险犹纪人群选择 为三零系列显卡已经特别厚特别长了,那四零系列显卡性能又高,工号大发量大,那三十七分就会厚,显卡长度也会越来越长,所以说给咱显卡配个支架,也不往这几年陪咱度过的漫漫长夜。