se3屏幕和苹果8拆机对比
粉丝2253获赞7893
相关视频
05:08查看AI文稿AI文稿关机取卡槽，拆下尾部螺丝，电吹风沿屏幕边缘一圈，加热到微微烫手。加热稍微烫一点，只是有点温度不好拆。 听筒方向不要翘，向喇叭方向下来一点，拖开上面卡扣，然后再翻开屏幕， 取下屏幕排线盖板铁片后，先断开电池排线， 注意这里台线下面的泡棉底下还有一个隐藏螺丝。 断开主板上所有排线连接，要把卡槽的推杆推回框里，主板才好拿下来。 粘贴散热贴的要点是按压贴牢，不留控股气泡，有控股不但形成隔热，还可能顶高。主板电池粘贴按压时注意不要滑到按键，台线弄断了， 然后主板下挤上导热凝胶， s s s s 走胶就行，无需涂抹，最多半只足够，不是越多越好。新手装机最好是先装震动和喇叭，再装主板，喇叭是压在主板下的， 需注意 喇叭左边的角是压在主板下的。 先扣电池排线，再粘贴固定电池，避免先固定后电池排线对不上主板。装好电池，先把电池连接断开， 然后粘贴一张新的防水胶，改散热操作，现在才完成一半。装好屏幕再继续下一步操作， 最后再把电池排线扣上， 然后粘贴主板上散热贴主板位置按压贴牢。 主板上挤上导热凝胶，最多我们搭配的半只就够，也就是差不多零点七克差不多了。这个采用的是陶氏化学的 t c 三零六零，最好是不要用硅脂，没有凝胶管，用久硅脂干了以后还粘的牢，以后不好拆。 凝胶采用陶氏的 tc 三零六零，日本电气化的 scrs， 莱尔德的特地六零七系月的 clg 四五零零，只要是世界一线品牌都是不错的选择。 苹果八可以直接开机， se 二和 se 三拆机后可能需要插电开机，所有功能测试一遍，一切 ok。 合上屏幕，完装。屏幕先从下往上扣听筒方向，再按压四周 为布罗斯拧上。收工。苹果八 s e 二 s e 三材料都一样通用。
378智可优科技
10:41查看AI文稿AI文稿this is the iphone s c twenty twenty two third generation disassembly if you want to see more videos like this make sure you subscribe and follow me on twitter so be notified when i upload a new video and if you need any tools， there are links in the description to start off the century needs to be removed next on the bottom of the frame there are two pencil up screws that need to be removed once those screws are removed when you apply heat to the front of the screen to loosen the adhesive around the frame and then a suction cup tool needs to be used to help gently lift the screen up and gain leverage so you can get a plastic pry tool end and work our way around prying off the screen now the screen is to be lifted up from the left to the right there are seven phillips then it be removed once the screws have been removed the metal place can be removed as well now the flex cable for the battery can be disconnected once the battery has been disconnected we can proceed to disconnect the rest of the cables in order to remove the battery there are two adhesive pull tabs on the top， which have to be pulled to release the adhesive underneath the battery， so the battery can be removed there are two more adhesive pull tabs on the bottom of the battery regardless i never seem to have any lick with those pull tabs so i'm going to apply some icer propol alcohol around the edges of the battery and let it sift for about thirty seconds， so we eat the way adhesive underneath making it easier to pry it off here's a better look at the two thousand and eighteen milliamp hour battery now the twenty twenty second generation iphone se looks almost， identical， both， internally and externally to the iphone se twenty twenty two third generation， but not one hundred percent the text or imprint on the coverings look different as well as the fact that the twenty twenty two generation three battery looks slightly thinner than that of the one in the twenty twenty se on the bottom portion of the battery where the chips are components of the battery as well as the flex cable are seem to be a bit thinner on the iphone twenty twenty two se possibly get slightly longer battery cell now as for the question if the iphone twenty twenty two se battery would work in the iphone twenty twenty the answer to that would be no size wise yes， it would fit in the compartment however， yet again， apple has changed the connector very slightly so the connector on the twenty twenty two se battery would not fit with the connector on the twenty twenty se here's a closer look at those connectors here's the licking on side by side another difference you can see the main board on the twenty twenty two se is slightly longer compared to the one on the twenty twenty se the bottom portion of the motherboard comes down slightly longer as well as the plastic piece on the speaker assembly on the bottom for the twenty twenty it's slightly longer on the top compared to the plastic on the speaker on the twenty twenty two now as far as we're placed in the screen from the twenty need to the twenty twenty two the connectors fit perfectly fine and the screen turns on and the display works fine however， the touch doesn't work properly， sometimes it'll detect a touch and sometimes it doesn't now physically between the two screens there are a few more differences one being the layout of the graphite film on the back， which helps transfer heat and the second thing i could see is that on the twenty twenty iphone se the second generation one there's a one piece metal plate on the back and the graphite film is actually on that metal plate compared to the twenty twenty two third generation one where there's a metal plate on the bottom and a separate metal plate on the top and there's nothing in the middle， so on the twenty twenty two the graphite film is attached directly to the back of the screen and when looking at it from the side， these two screw holes on the frame or empty since there's no middle plate on the back right there compared to the one on the back of the twenty twenty where these two screws are in place holding the back of the mid plate in the mid section the same goes for the other side where there's a screw missing over here on the twenty twenty two compared to the twenty twenty so from the looks of it you wouldn't be able to swap the parts between the twenty twenty and the twenty twenty two so now let's continue that this assembly there are six phillips screws and seven tripoint screws that need to be removed once the screws are removed we can begin to remove the covers the flex cables for the screen are adhered to this bottom plate， so if we need to replace this we'd have to heat it up and pry that plate off the flex cable for the home button is connected here and that cable can be disconnected by just popping it off and the home button can be removed by pushing it in and removing it here's a better look at the front facing camera the top ear speaker and the proximity flex and this entire flex cable assembly is held on with adhesive， so if you need to replace that you'd have to just gently pry it off now back to the main board， we're going to proceed to disconnect some more flex cables there's a standoff screw and a phillips screw which are holding down the cover that's covering the main camera that need to be removed here's a better look at the twelve megapixel white camera and this camera has ois or optical image stabilization there are seven more phillips screws and two more standoff screws that need to be removed two more flex cables need to be disconnected as well as two more phillips screws there are two more phillips screws on the inside of the frame that need to be removed now this flex cable can be removed as well as the antenna flex cable on the top right side at this point there's one more standoff screw that needs to be removed once this rubber gasket is peeled off there's a phillips screw underneath that needs to be removed now finally after all the screws are removed the main board can be lifted up and removed here's a better look at the main board there are rubber gaskets around the connectors a look at damage indicator， which is white sticker over here on top and graphite film over the shields to help transfer heat when the graphite film on the front is peeled back there's nothing visible underneath since the shield is covered and soldered to the main board， there's more graphite film on the back shields here's a better lick with the graph i film on the back removed once the main board has been removed we can see the wireless charging coil on the center cover with graphite film tap transfer heat as also more graphite film which lays underneath the motherboard there are nine more phillips screws on the bottom that need to be removed as well as one tripoint screw does a flex cable between the taptic feedback motor and the speaker assembly that needs to be disconnected and the speaker assembly can be lifted up and removed here's a better look at that does a mesh filter inside the speaker assembly opening and here's a look at the bottom this pasta cover can be removed there's a standoff screw and then there are three more fill lip screws that need to be removed toward the phillips screws are on the inside of the frame on either side of the charger port once the flex cables lift it up the flex cable for the tactic feedback motor underneath can be disconnected here's a better look at the taptic engine now the two microphones on the bottom is to be separated from the frame and they're held on with some adhesive and then the charger port flex cable can be peeled off the charger ports located in the center and the two microphones are located on the other side here's a look at the other side of it the toggle key for putting the phone in silent mode， the volume keys， the flash， the secondary microphone and the power key are all attached to this one flex cable which connects to the main board with this connector so if you need to replace either of those you'd have to remove the phillips screws， which are holding the metal brackets on the inside of the frame， which are covering the flex cables and holding the keys in place and you'd be able to peel off this flex cable and replace it for the repairability score i give this phone a five point five out of ten now start to put the phone back together once everything's back in place apply new adhesive and reply the screen power on the phone and you're done i hope you enjoyed this video and i'll see you in the next one。
77油管科技TV
01:29查看AI文稿AI文稿大家好，我是伟伟。今日凌晨，苹果发布了 c 三，身为魔改界的靓仔，决定拿出成年已久的小八个给他魔改下，全过程来了，不要眨眼哦！ 外观升级完成，型号五 g， 安排 该西第三代最小的五 g 手机，系统顺畅无比， 相机拍照清晰完美。更多魔改关注伟伟， nice！
1541玮胜科技数码
00:23查看AI文稿AI文稿第三代 iphone se 的首次拆解已经在视频网站出现，显示了该设备内部组件的外观。拆解结果显示，新的 iphone se 拥有更大的二零一八毫安时电池，而上一代机型为一千八百二十一毫安时。根据苹果公司的技术规格，与上一代机型相比， 新的 iphone se 在充满电的情况下可提供额外的两个小时的视频播放，以及额外的十个小时的音频播放。
232机智数码
00:56
05:39查看AI文稿AI文稿大家好，这里是高科技，我是杨振林。新款的 se 呢，外观造型啊，跟 iphone 八保持一致，但是还是可以区分的，背面的 logo 呢挪到了中间，底部的 iphone 字样呢也跟十一一样被取消了。小尺寸的手机呢，我 我是比较喜欢的，因为他比较适合单手握持，那用起来也比较舒服，那如果还是全面屏的话，那真的就是完美了啊啊，只可惜他只是 iphone 八的升级版，那他到底升级了什么呢？就让我们拆开一探究竟。先取出卡托， 卡托呢，外圈是设有防水防尘的胶圈，然后呢再关机，再拧一下尾部的两克螺丝。 拆苹果的屏呢，从来都不用加热啊，直接平到口，从底部呢卡入， ok 敲点起来啊，然后呢记住下指甲扣着，这样就可以了，顺势呢从两边划开啊。 哇，真的跟 iphone 八一模一样，我们拿个过来看一下啊，这样看的话呢，电池的大小，震动，然后喇叭，主板像头啊，天线，包括这些盖板都是一样的哈，好像就是一个手机。 先拧下底部盖板的螺丝，取下盖板后呢，先断电啊，再拧下顶部的盖板螺丝，取下盖板后呢断开前置排线，断开屏幕的排线， 指纹排线。这个屏呢应该是跟 iphone 八通用的啊，展一样嘛是吧，这边呢我也准备了一台 iphone 八，刚刚拆掉啊， 然后呢直接拿这个瓶装上去看能不能亮， 哎，亮起来了啊，那证明呢，这个配件呢，通用性啊，是非常强的。好，我们接着往下拆， 整个外配部分呢，基本上都是跟 iphone 八一样的啊，升级的话可能也就是他的 cpu 了。那接下来呢，我们也不用去拆解了，因为都一样是吧，直接把这张主板取出来，拿一张 iphone 八的装进去，然后我们开机测试功能，看看这些外配是不是都可以通用。 呃，这样啊，我们直接拿一块 iphone 八的主板，因为他这个扣子什么都是一样的，我们直接装进去，然后开机试下，看功能会不会正常啊， 他这个电池的扣子呢，是不一样的，跟 iphone 十一的一样，所以我们要拿一块 iphone 八的电池才可以 黄开机试一下， 亮了啊， 解锁先试一下声音， ok， 震动也可以啊，震动也可以的，听懂这边也有声音啊，也有好照相。哎，相机不行啊，前面 切不过来了，应该相机是不通用的，闪光灯开一下也打不开啊，也打不开。然后呢，我考虑到可能是由于他这个后摄像头不通用，前摄像头应该是一样的，所以我就把这个屏又重新扣扣回来，我们再试一下啊， 嗯，可以，一切 ok， 前线头也是通用的啊啊，经过测试以后呢，发现基本上的外配都是可以通用的，只有后置摄像头不能用。然后电池呢，是因为那个电池的座子它稍微大一点，跟十一的一样，所以也是不能用的。 那么接下来呢，我们先看主板啊，他是不是也差不多？好吧，主板的整体布局呢，还是和 iphone 八一样， cpu 升级成了 h 三，除了电池座以外呢，其他的排线座子全部通用。背面除了中屏大小，电源和 wifi 是不一样的，其他也基本通用，带来的好处呢，就是方便维修。这是所有桌子的测量参数，放图片给大家参考一下。 新款的 se 呢，除了 cpu 以外，其他的基本没有什么升级，外配呢也差不多，除了后摄像头和电池不一样，其他的都是跟 iphone 八一样啊，可以通用。 这次呢，苹果真的是够省的啊，我本来还兴致勃勃的，但我总不可能跟大家再讲一遍 iphone 八的裁剪，你说是吧？啊，喜欢的小伙伴呢，可以数字三连走一波，我们下期再见。
2.9万艾奥科技
04:25查看AI文稿AI文稿我靠，你这苹果八怎么能用两张卡，哎我靠，牛逼，类似一台粉丝发过来的 se 三，要求扩容五百一十二 g， 然后给双卡。我们先看一下手机是一台美版的，然后内存啊，六十四 g 非常的不够用， 他说之前在外面换过这个后玻璃，然后无线充电呢，也用不了， 今天呢想把手机升级一下这个内存啊，他说六十四 g 啊，根本就不够用，然后呢平时也用到双卡，这个手机啊只支持一张卡 很不方便，所以要求我们给他改双卡，然后加扩容五百一十二 g。 我们首先将这个主板给他拆下来，我们可以看到之前换后玻璃把这个主板都 已经捣烂了，这个呢就是全新的五百一十一十二 g 的这个硬盘，我们首先将硬盘周边的边胶给它割掉哈，然后慢慢加热，我们首先将这个六十四 g 的硬盘给它取下来，趁热哈，打上焊油， 然后将这个焊盘上面的黑胶给他刮干净， 好，刮干净以后擦干净，刷干净以后，我们打上少许焊油，将这个焊盘进行最后一次这个清洁， 将硬盘后面的这个焊点全部给他拖干净，然后放入直线网，我们直入这个西江，看这个 效果是不是非常的哇塞，颗颗饱满。我们打入少少点注焊剂，我们将硬盘放上去，风枪慢慢加热至 qq 弹弹的，感觉硬盘就安装可以了， 因为需要改双卡。首先将这个 ecm 芯片给它拆下来，我们将第二张卡芯片放到这个主板上，利用这个铜线啊，将这个手机卡与这个主板进行一个连接， 我们需要连接五条线， 好，线接好以后 清洗干净，我们将这个断掉的这个无线充给他接起来，如果觉得这波操作可以的话， 麻烦送我一个免费的小心心，玉哥在这感谢大家。简易的一个安装，然后用爱思进行一个刷机， 刷机完成以后我们使用密码进行激活，激活完以后我们看到啊，存储量已经变成了五百一十二级，我们将主板上面的所有螺丝给它固定起来，慢慢的将这个电池取下，为什么要取这个电池呢？我们接下来往下看， 电池取下来，将上面的残胶清理干净，取下电池，我们发现这个电池已经鼓包了， 这样的话是非常的危险的，我们将上面的保护排线给它取下来，给它焊接一个全新的这个电芯， 大家注意哈，这个是 se 三哈，他的那个电芯跟七代八代是不一样的，他是反的哈，所以的话焊接的时候一定要注意。我们将电池给他安装上去， 清理干净里面的灰尘，装好这个屏幕装好，挡板 打好，螺丝扣上屏幕，打上尾部螺丝 插入。第二张卡我们看到啊，双卡已经来了哈， 然后再看内存啊，已经变成五百一十二 g， 卧槽，牛逼，所有的功能呢都是正常 两张的卡的信号也是正常的，不要忘带了，暂不要忘记了哈，记得关注再走哦。
922芮哥卖机·宣城分期包过
00:16查看AI文稿AI文稿这是苹果最新款第三代 ac， 打开看了内部结构，这不就是一台完整的八代吗？除了电池标志位置改动，屏幕铁盖子都给予资源改成两小段，也只有苹果有勇气这么改款新机。
135昆明宁恩手机维修
