粉丝938获赞4109

今天给大家分享一下我们这个回字拐角的贴法,大家可以看到我们这里是一个回字的拐角,那么首先呢我们需要把膜平铺上面,平铺之前我们确保保护层已经揭掉了,平铺上去以后,我们在膜和台面之间喷洒大量的水,确保膜能在台面上自由的移动。我们铺好以后呢, 我们在膜上把拐角的位置标记出来,我们这个时候呢可以用记号笔或者是眉笔点好拐角的位置,然后沿着记号把它轻轻的划开, 这个时候划开的时候呢,我们需要略微的比我们的这个拐角的实际的宽度要稍稍小一点, 因为这个时候是为了防止我们切的时候刀切歪有误差,造成我们贴上去会很难看,因此我们先切的稍微小一点,那么切好之后呢,我们就可以把膜往里面的推 啊,就如果说你的这个拐角处的话,这张膜这边后比较长的话,可以两个人左右一起推,推进去的时候我们会发现呢,就是因为我们划开的这个口是稍稍小于我们的回字形的这个区域的,所以推到一定的位置的时候,你会发现有点紧绷推不动了, 这个时候我们可以把这边稍稍再划开啊,划开你就发现把这个洞再扩大一点,他就能推到能推到底了。切好之后我们来把所有的这三条边来精确的把它修修整好, 修整好之后呢,我们要开始把所有的这个这一整面的这个台面把它进行一个仔细的刮水,那么刮水的过程也同样是要刮到三到五遍,拐角处我们要多刮几遍,因为这个地方拐角比较多,刮水的时候可能不彻底。

you will learn how to successfully apply dinoc brand architectural finishes to tabletops you will learn two ways to wrap the film around corners one is by conforming heated film around the corner, the other way is a cut and overlapped corner which is the preferred method before applying film always clean the substrate to be sure it is free of dust and contaminants wipe with a solution of seventy percent, isopropyl, alcohol and thirty percent water and wipe dry be sure your hands are clean and free of dirt and motions to avoid contaminating the adhesive and always work on a clean surface with clean tools you will need these tools a cutting tool with breakoff blades a three m brand applicator pa one gold squeegee protect one edge with a soft loop side of three ams hook and loop tape or a three am brand low friction sleeve pa one or soft cotton cloth wrapped in tape onto the squeegee a liner cutter this tool has a guide under the blade that slips between the film and liner so you cut only through the liner one option is seambuster a product from advanced equipment manufacturing it is available online and at many major hardware and home improvement stores three m brand adhesion promoter three m's primer ninety four is a solvent based product and three m brand sandpaper to determine the length of the film that you'll need to cover the table top measure the length of the table plus the height of the table top edge times two plus eight more inches apply three and brand adhesion promoter to the edges of the clean table top using the brush allow it to dry for five to fifteen minutes about eight inches from the leading edge of the film use the liner cutter to make two straight parallel cuts through the liner about two inches apart and remove the liner from that area make the cuts as straight as possible, which will allow removing additional liner easier as you move through the application lay the film on the table top so the exposed adhesive is a few inches from the edge of the table lightly adhere the film to the tabletop using your hand remove a few inches of liner from the film use an edge protected squeegee to adhere the exposed adhesive to the tabletop the proper squeegee technique is to work from center to edge center to edge always pushing the air to the nearest edge and using firm overlapping strokes lift the film and roll back a few inches of the liner while holding the film top with one hand start squeeging where the film is already adhered remove the rest of the liner and squeegee just to the edge of the tabletop for purposes of this video, we are only showing a partial tabletop installation first, let's look at how to wrap a corner by heating and stretching the film working on one corner bring a heat gun to about two hundred degrees fahrenheit holding the gun about six inches from the film pass it back and forth over the corner area of the film until it becomes warm and relaxed use care not to overheat the film or burn your fingers working quickly put down the heat gun on a safe surface, but don't turn it off grasp the edges of the film to stretch and conform it over and slightly under the corner of the table top with your fingers conform and adhere the film to the corner just on the vertical sides heat the film on the vertical table edge adjacent to the corner hold the film with one hand while squeeging the table edge use care to avoid creating wrinkles continue heating stretching and squeeging the rest of the film on the table edge stopping about an inch from the next corner notice how the installer is using the edge of his squeegee to stroke downward and make a clean crisp edge now heat the film and squeegee the table edges on the other side of the corner later you'll see how to finish the bottom edges of the table use the heat gun as needed to keep the film warm as you can form it to the table's edge repeat the procedure for conforming the film to the other corners of the table now let's look at how a corner can be finished with an overlap identify the exact top corner of the table top cut the film from the underside starting at the corner of the table roll back one side of the film, while wrapping the other side around the corner adhere it with your fingers first to shape it and then use the squeegee to get a good bond trim the wrapped part of the film to about one half inch from the corner cutting it all the way out to the edge of the film and then remove the excess apply adhesion promoter to the half inch wide piece of film that is wrapped around the corner allow it to dry for five to fifteen minutes allow the film that has not been adhered to gently lay over the edge of the table top using your fingers adhere the film over the top edge making a clean crisp edge hold the bottom edge of the film with your fingers to create some tension which helps avoid wrinkles use a squeegee to firmly adhere the overlap of the film at the corner and then squeegee the remaining edge of the table top on that side stopping an inch or two from the next corner to remove excess film at the overlap area hold the blade at a forty five degree angle to the flat edge of the table top and carefully cut away the excess film now refine the edge by very gently and lightly sanding any rough edges using a piece of fine grit sandpaper now finish the bottom edges of the film use a clean sharp blade to trim the film along the bottom edge of the tabletop just as you did with the overlapped corner finish the bottom edges of the table top by very gently and lightly sanding any rough edges using the sandpaper that's how easy it is to transform a tabletop with three m's dinoc brand architectural finishes 上淘店搜索三姆来科技馆了解更多。