粉丝5.7万获赞7.2万

今天教大家装连立包豪斯 o 十一 d evo rgb, 我 们看一下装机准备工具以及我们装的配置。壁纸刀,水口钳, 这个小剪刀, ph 零的螺丝刀, ph 二的螺丝刀,装白色机器啊,白色扎带若干 cpu 九七零零 x, 这一个五点零的八幺零零,一个 g m 七千的一 t, 一个五点零,一个四点零,两根女武神的六千 c 二八 a 带 华硕的 b 八五零杠 a 吹雪 s 四零七零钛的白火神机箱风扇,我们这里用的是十把的积木,一代 v 三无限版本加三把水冷自带的 fc 七百 采用的是一个夹汉堡的安装方式,追风者 j h 八五零的白色,加两根霓虹线,水冷是泰坦的 l g 七百 pro。 下面我们开始装机操作。第一步,打开扣具压杆, 放入 cpu 啊, cpu 左上角有个小三角对着主板这边,小三角也就是正着放进去, 可以放进卡槽以后可以手动确定一下位置。 cpu 放好以后,盖上扣具,用这个压回压杆锁住,取掉这个保护盖。下一步我们安装固态,我们五点零的固态装在第一卡槽,这个第一槽位就是五点零的速率。 第二块四点零的盘我们装在 m 二的第二槽位。这张主板第一槽位和第二槽位都是直连 cpu 的,是不会有带框问题的, 注意的是第三第四这个板子一共是四个位置,第三,第四,第四槽位不受任何的冲突。第三槽位和这个第二 pce 乘十六的卡槽共享通道只能二选一,如果这里插设备的话,这个 m 二这个卡槽就失效。 四十五度角插入,按下锁扣,如果你是新主板,记得把这个保护膜揭掉,这里我是装过,所以就已经揭掉了。装回 m 二的散热马甲, 不用拧太紧啊,就是这个马甲不晃动啊,看到固态完全贴合上就可以了,拧太紧容易造成 m 二的变形弯曲。固态装完,下一步我们就装水冷,因为我们这个是拆卸过,所以需要重新涂抹硅脂 刮一下,刮平 刮这个操作不是必要的,如果自己整的话,可以直接打个叉或者点几个点就可以了, 效果也基本一致。 ok, 涂好硅脂,我们装上水冷, 装上水冷风扇,水冷风扇这一层我们装这个积木的背面夹汉堡装风扇,原装的装上积木的连接器 固定冷排风扇对角固定,盖上这个装饰角, 这个能把螺丝给遮住, 把这个线进行预处理一下。 水冷的水冷一共两根线,一个是这个屏幕的数据线, usb 线,一个是水泵的供电,水泵供电,我们插到主板的这个 a l p u m p 接口也就是这个, 这个线用扎带收束一下,大概绑到这个位置就可以了。剪掉多余的扎带 先放一边,我们上机箱,先把机箱玻璃都取掉,顶部的这些盖板,这个玻璃是卡扣的,直接扣就行, 硬盘盒也直接取掉, 放倒主机装上连接器啊,这个是后排风扇,后排一把正叶的十二厘米 安装主板 固定主板固定,主板螺丝是用这种机箱自带的螺丝盒里有这种规格的 交叉固定。固定螺丝之前一定要确保你这个孔位啊,都居对住有主板螺丝柱和你主板的这个螺丝孔位对着,确定装到位以后再固定, 把这个 usb 的 线直接从这个孔位顺出去, 这里多余的线我们整理一下,直接一会就藏在这个顶部位置了。 cpu 供电线,我们装水冷之前把这根线也装上, 稍后也收拾一下。 顶部这里我们观察一下接口啊,供电接口只剩一个 cpu fan 和一个 cpu opt, 然后我们要接这个冷排的风扇,还有夹汉堡的风扇,需要两个接口,后排这个风扇没有没有接口了,没有接口,我们这里用一个延长线,因为底部这里供电接口多,把它延长到底部去, 同样从这个孔穿出去一会,背面的线统一处理,把这个杂线乱线整理一下, 都整理好以后我们就可以放水冷,水冷的线也可以直接先接到接口上去,这个是靠近水冷一端的,这个我们接到 cpu fan 的 接口,这面的风扇处理好以后,我们就可以 放上水冷了,然后把夹汉堡的风扇准备出来。夹汉堡风扇就是不浪费水冷的风扇,针对这个机箱顶部高的情况也能 也能起到一定的装饰作用。这个是磁吸的,相对还好操作一点,很多风扇你三把的话,你一起拿着都不好拿。 这个风扇是需要反着装的,因为它是风,风向是这样的,这个是正压风扇,所以我们这样装, 一只手托着另外一个手去固定对角固定两颗以后,其他就可以直接去固定了, 同样也是尽量去交叉固定,这样受力好一点。然后也能发现一些问题,比如说你这个风扇没有装水瓶,你就找不到孔位。 夹汉堡出来,这两组线,一个是供电,一个是灯光,我们直接接到主板的这个闪光同步接口, 同样用扎带把线收上去就可以了。 这个多余的线,我们可以依靠背面的孔位把扎带伸进去固定一下, 长出来,这些线叠起来扎带固定, 稍微整理一下细节, 我们可以看到最终的效果。虽然夹汉堡了,但同样顶部非常简洁,这个水龙头就可以装回去了,水龙头磁吸供电,这时候我们就可以装侧边和底部的风扇了, 侧面和底部全是反页,一共是六,把反页 推上连接器, 先固定侧边 这个侧边的供电线,我们直接可以从这个孔位穿出去, 这样的话一会可以和背面这些 i o 出来的线一起整理,前面看起来会更干净一点。 安装底部风扇,底部风扇这里有一颗螺丝,从右向左推,推了之后就可以拿出来, 我们可以先确定一下位置,尽量上下保持垂直,这样会更美观一点。 这个直接从这里穿出去, 放入滑轨啊,从右向左推,固定回这颗螺母, 转过来我们处理背面的线, 背面这些线一共是,我们看一下都有什么线,这个是 c 口线,这个是音频,这个是 usb 三点零开关机的一体跳线 前面板的灯光,前面板这个是刚才侧边风扇的供电,这个是前面板的供电,这个是底部风扇,一共这些线,我们先处理这个 c 口线和 usb 三点零啊,通常在主板的这个二十四 p 位置,先把这两根线处理一下, 从这里穿出来,找到对应的接口直接插上,这接口是防呆的,如果你一个方向插不插不进去,就换个方向 扎带,顺着向下固定就可以。先找到一个锚点, 处理到大概这个位置就可以稍微停一下,然后我们把其他的线处理一下,到时候这里会有很多并线,要一一块一块绑,对,这会绑了一会可能还要拆开,避免不必要的这个 开关机的跳线,直接绕过来接到主板的右下角,这里 上面有写 f p n e l 这里。因为我们有霓虹线啊,所以我这个霓虹线得先穿过来,我直接把这个卡扣先去掉再穿,带着卡扣不好穿, 去掉以后一定慢一点,因为这个霓虹线你去掉卡扣以后,他这个比较薄入啊,你一旦折断了之后,这个灯就不会亮了。 ok, 穿过来以后我们把这个卡扣装回去, 我们可以临时先用个藏扎带把这个霓虹线给吊着, 继续处理我们这些线,这个线大概绑到这个位置以后,我们把这个音频线也插上穿,从右下角这个孔穿出去,接到主板的左下角 a u d i o 转过来,这个是待会连接电源的 sata 这个神光同步线,我们也接上这个,待会我们也用那个接收器的那个 sata 供电,这两个都是,所以这个线也接过来, 这个线直接接到主板的五福三针。 ok, 转过来继续处理这些线处理好以后大概是这个效果,剪掉多余的杂带。 ok, 然后我们把顶部这些线放下来处理一些,这些线一个风扇的供电,一个是这个 usb, 也就是水冷屏幕, 顺着往下扎就行了,这个不需要什么技巧, 然后这个待会儿统一还是串到那个萨塔出来的。一分三供电 就是这个线,这个无线版本接收器里会带一个这样线,萨塔供电出来共三个,四聘的出来三个这个风扇的供电,这个供电会更稳一点,特别是如果你的风扇是连力的 lcd 版本,一定要优先接这个。 这里主板的二点零,我们直接从这个孔位穿出去,插到主板的二点零接口。 二点零接口通常在主板的底部啊中间位置,上面有 usb 二点零字样,同样把多余的线藏到这个底部去。这这个位置是一个电源仓, 这个线用上这个线我们直接接上。这个是侧边和底部的风扇供电, 这个是顶部,刚才我们那个后排的一个风扇都统一接到这上面, 然后萨特供电 装上电源固 定,电源对角固定 c p u 供电线,这时候可以直接接上,包括这个 sata 供电, 长出来的这些线也扎起来藏到电源仓下面。 这个线处理差不多,我们就转过来处理这个主板的供电。 处理主板供电的同时,我们可以直接把显卡装上了,因为我们确定一下这个这个霓虹线的长度以后,我们再处理背面线,统一处理,直接装显卡。 如果你小白没有什么经验啊,尽量是把主机躺下装显卡,接上霓虹线的供电。 霓虹线主板二十四片,这里也是霓虹线,直接穿出来这个卡扣往中间调整一下,接上霓虹线。 通常这个接口位置我习惯是夹扎带固定一下, 因为这个霓虹线他转接时间长了,这个接口容易松动,大多数烧接口的情况就是这个接口松动了,所以我们直接给他物理上绑死 扎带扣朝内,倒也影响不了多少美观。主板供电和这个显卡供电我们一起插上一块处理, 插到对应的接口上去,这接口一定要插牢啊,一定要插牢,这里有线书,我们就用上叠到一块统一整理, 插到对应的接口上,最终背线收完就是这个效果。看一下正面, 正面我们把最后两个内存装上,四槽主板优先插到二次,从左向右数啊, 把这个硬盘盒装回去, 最终背线的效果就这样。

as a complete redesign of the classic, o eleven d evo is a combination of innovations inspired by the o eleven, d xl, o eleven, d mini, o eleven air mini, and of course users feedback starting from the outside the mesh design at the top and rear of the case has been updated to provide wider areas for air to pass through while still offering adequate dust filtration the new pin mounting mechanism for the side panels means they can be removed without the need to first remove the top panel eliminating an unnecessary step when trying to access the inside of the case additionally both glass panels can be locked in place to prevent them from falling out during a transport at a depth of fourth sixty eight millimeter a width of two eighty, five millimeter and a height of four forty six millimeter the oeleven d evo is slightly deeper and wider than the original oeleven dynamic giving it better compatibility for large components in terms of hardware compatibility the oleleventy evo can support motherboards from mini itx to eatx four twenty millimeter long gpus up to three sixty or two eighty radiators at the top inside and three sixty at the bottom as well as a one twenty radiator fan at the rear one of the main features of the oelevendy evil is its ability to be reconfigured into reversed mode with everything included this process can be completed and only a few steps after removing all side panels the aluminum and io module can be removed you'll then be ready to remove the base of the case then flip the frame upside down make sure to relocate all internal parts cable management, bar drive cage and psu support at this point the base of the case can be reattached to the frame and all side panels can be inserted back in place just like this users can reconfigure the airflow pattern of their system benefit from a full view of the computer parts even when placed on their left to make the front panel as clean and aesthetically pleasing as possible langley created a multi directional button that can be pressed from both the front and side of the case right below the power button and move to the side of the case for a cleaner front panel are the reset button and the led control button also the front i o which includes a usb three point, one type c, two usb, three point, o type a and an hd audio mic port had been designed into a removable io module this module can be relocated from the front to the side and even rear without the use of any tools users also have the option to increase their io count with the additional io module kit which doubles the usb port of the o eleven d evo and for users who prefer to have their case on the floor an additional top io kit is available to relocate the original io into the top aluminum strip of the case to ensure better air circulation while using a water cooling setup an additional upright gpu kit has been this provides the user with an option to open up the main chamber and create a true chimney style configuration when doing custom water cooling or using aios to make the upright gpu kit work careful attention to radiator clearance was taken to make sure there's no interference with radiator support therefore the radiator mounting bracket has been moved closer to the side glass panel this ensures radiators as wide as one thirty millimeter and fans as wide as one twenty millimeter can still be mounted when installing triple slot gpus in the upright gpu kit in addition, a brace has been engineered to prevent upright gpu from moving around adjustable in multiple directions the brace can support anything from thin water blocks to thick triple slot gpus and to further improve cooling the additional mesh front panel kit can be installed to replace the front glass panel and provide direct airflow for systems with cpu cooling towers where systems with air cooled upright gpus in addition to the mesh front panel brackets are included to provide mounting support for three one twenty millimeter fans or two one forty millimeter fans and for users looking for a more traditional vertical gpu option an additional vertical gpu kit is available its design has been inspired and improved upon the original vertical kit for the oalevend the kit's mounting location has been elevated leaving up to fifty millimeter of clearance for bottom radiators and fans and can be raised up even further to allow up to ninety millimeter of clearance for thicker radiators and fans and for users who prefer horizontally mounted gpus the olevendy evo comes equipped with the gb zero zero one anti sag bracket which is functional in both default and reverse layout in the main chamber of the olelevendy evo even the top and bottom mounting brackets have been well thought out multi purpose and design each bracket can support either four ssds two hdds up to a two eighty or three sixty radiator and two one forty millimeter fans or three one twenty millimeter fans both top and bottom brackets are identical which means they are interchangeable and feature a quick sliding mechanism for speedy insulation and removal and both brackets can be quickly secured in place with a thumb screw beside the motherboard a reversible mounting bracket can support up to a two eighty or three sixty radiator and two one forty millimeter fans or three one twenty millimeter fans secured in place by a toolless latch the bracket in its original position provides support for an eighty four millimeter thick radiator fan combo and then reverse up to one twenty one millimeter fan radiator combo moving to the second chamber of the ol md evo, the space beside the motherboard can be fitted with a hard drive bracket that can take either two htds or four ssds next to it the cable management bar can support an additional two ssds and the perforated drive cage can support multiple configurations such as two hdds or ssds in the trace, an additional ssd can be mounted on the side of the drive cage this location also supports a hub mountain and at the top of the drive cage the user can mount either a fan hub or a sixty millimeter fan in total an impressive nine ssds or six hdds and three ssds can be mounted in thirteen different locations in the oelevendy evo, the cable management of the lmd evo has also been modified while tie points are available behind the motherboard tray for velcro straps a new hook style cable management bar allows for easier cable placement by holding bulky cables under hooks and keeping cables in place while routing everything lastly even the rgb strip of the olmd evil has been revisited to improve as user felliness in addition to being able to control the light effects of the rgb strip via the led control button and via the motherboard software they also features a header that can plug into the uni hub allowing it to be handled via alconite with the oeleventy evo lean lee hopes to simplify the pc building experience while offering a wider array of configurations that displays and cools the pc in the best fashion possible。

今天到移民广场给帅哥换一个机箱,联利包豪斯欧十一威选五零九零显卡颜值性能拉满,因散热器设计问题,暑装冷牌会导致水冷屏幕方向装反,影响视觉体验。但帅哥是细节控还是联系我重新调整冷牌位置, 这也导致无法安装三面透视玻璃,不过也不太影响这台包豪斯旗舰海景机箱的颜值。让我们一起来欣赏一下这台主机 uh huh huh。

我们仓库啊,最近又到货了一大批的机箱,其中像这款联力包豪斯 v 轩 complete 我 就想不明白了,这款机箱现在这么火热吗?究竟是什么原因让他那么受欢迎呢?我想一定是因为他三面高清侧透的玻璃,再加上联力自己本身不错的做工用料,还有就是加上我们家九点零二寸可自 定义富平,完美展示了什么叫颜值及正义。像这种机器啊,我们装过老多台了,装机师傅呢,对这种机箱的一个走线呢,布局以及平常大家可能不会注意到的一个小细节,都已经打磨的淋漓尽致了,所以有需要装这款机箱的小伙伴呢,一定要联系我们哦!

他被夺走生命时,一岁半的孩子和妻子就在看台之上,安道尔门将奥沃诺用一记恶劣至极的非膝动作带走了这位用尽全力只为圆自己一个职业梦的年轻父亲的生命。可就在残忍的袭击了对手的心脏后,当事人甚至没有回头关心一眼倒在地上的德米格尔 冷血的扭头便走向场边。在现场目睹一切的球迷被彻底激怒,用最大的辱骂声 回击着这位拥有金字般的心的善良门将。相较曾同台竞技的天才球员,现年已满三十岁的德米格尔却用了二十年时间才首次触碰到梦寐以求的蜥蜴联赛。是他与特内里菲的双向奔赴成就了一切。而事后 俱乐部主席和最大股东就一直守在医院外,随时为他的亲友提供一切可能的帮助,接受采访时一度声音哽咽,满含泪水。 回顾德米格尔的职业生涯,可以用坚韧而忠诚来形容,二十六岁前 能够站上西乙赛场,成为一名职业球员一直是他最大的梦想。直到二零二四年,在卡斯特利翁的第二个赛季终于迎来了大爆发。当赛季狂轰十六球的他,在经历了二十年的摸爬滚打与升级决赛惨遭逆转的巨大挫折后, 他终于实现了自己的职业梦想,并在二十七岁那年完成了西乙首秀和职业足球的首例进球,结果他很快又被教练死死摁在了替补席上。 就当他以为会再一次落入谷底时,是特内里费一次又一次的电话邀请感动了他。或许在外人看来,再次离开悉尼加盟第三级别的特内里费,代表着他多年奋斗的职业足球梦想彻底破灭,而他却从不这样认为, 因为他知道他会用尽全力回报这支信任他的球队,帮助他们再次重返西乙联赛。而就在加盟的第一个赛季,他就以打入十一粒进球的表现兑现了升级西乙的承诺,亮眼的表现和宝贵的升乙经验让他在那个下窗吸引了多支球队的报价,可都被他直接拒绝。 他说他只想全心全意的为特内里费效力,如今在主场穿着心爱的球衣倒在了冲锋的路上,或许对他来说也是一丝慰藉吧。

在抖音拉黑对方,你知道对方会显示什么吗?如果对方把你抖音拉黑了,那么你也搜索不到他的抖音了,也看不了他的抖音作品了,把抖音拉黑,对方的显示页面就是这样子,接下来呢,用实操呢告诉大家, 在抖音拉黑对方,对方的抖音页面显示是什么样呢?可能很多人都不知道的,我们先点下三个点, 把这位好友的抖音拉黑,先点一下拉黑,然后确认拉黑,那么现在呢,我们就把好友拉黑了,拉黑之后呢, 这里就写到,对方已被你拉黑,你已拉黑,对方无法查看其作品,就是说这个好友的 抖音呢,已经被你拉黑了,那么拉黑这位好友呢?如果这位好友呢,想看我的抖音是吧?那么他就会显示这样子, 暂无内容,有无于对方的隐私设置,你无法查看他的作品。如果呢,你出现了这个页面,你 点开那个好友的抖音,出现了这样的页面,是吧,那么就证明呢,他已经把你的抖音拉黑了,你看不了他的作品了,就算你在搜索放大镜里面呢,也搜索不了他的任何作品,任何内容,是吧? 当你打开好友,出现这个情况呢,就是代表对方已经把你拉黑了,相信呢,很多人都不太了解这方面的知识点,可以分享转发出去,让更多人知道哦,关注小红,每天分享不一样的知识点,我们下期再见,拜拜!

如何通过对方的手机号来找到他的抖音号呢?假如你去放大镜里面去搜索呀,可能你是搜不到的啊, 不要着急,接下来我教你一个小窍门,只要你学会了这个小窍门呀,我们就能快速的在我们的通讯录里面找到所有朋友的抖音号了, 同时我们也能看到他发的所有作品,是不是非常的神奇?那废话不多说,我接下来给大家上实操,你不要眨眼睛啊,担心自己看一遍记不住的小伙伴们呢,你可以点赞收藏保存下来,你方便,有时间了就跟着一块操作吧。 首先我们先把好友的电话号码添加到通讯录里面,接下来点击右下角的我,然后看到这有个添加朋友没有,我们点击打开,这上面有个通讯录,我们点击一下通讯录,好,这里面就是我 我们所有通讯录好友的抖音号,你比如说想看他发的作品,点他头像直接进他主页里面看他的作品就可以,这里还可以添加他为好友,学会了吗?还有哪里不清楚的,欢迎评论区给我留言,关注我,我是静心,每天带大家翱翔抖音的知识海洋。