小车移动出去以后,首先要打开它的第一号盖,按住蓝色的卡扣往外掰,二号盖往上抬,现在可以看到打印头,打印头可以取出, 先打一头放入 合上他的二号盖,再合他的一号盖, 然后关闭,然后关闭上护照 机器吸引硬墨,吸完硬墨以后自己做打印头调整,如果未装置会提示你装置。
粉丝868获赞2246

先拆掉机器右边的侧盖,一共四颗螺丝, 拆掉螺丝后,打开墨盒盖子就可以取下边侧盖了,注意卡扣,禁止暴力拆卸。 拆下边侧盖后,再拆掉这两颗螺丝跟清洁单元上面的这两颗螺丝。 拆掉升降电机组件上的两颗螺丝, 双手平拉出来,拔掉声 降电机组件上的数据线,这样就拆下了小车升降电机组件用螺丝刀逆时针旋转清洁单元锁扣齿轮会听到咔咔的声音,这时用手可以推动小车,将小车推离清洁单元上方后,我们就开始拆清洁单元, 清洁单元上面一共有两颗螺丝固定。 拆掉这两颗螺丝后,拔掉所关联的数据线,双手拿住清洁单元组件平拉出来,取下来的清洁单元带有废沫,小心注意别弄脏衣物跟环境。感谢关注!

呃,今天呢接到这个一个报销电话,他说这个机器的这才是五二零机器的这个左边位置,那下方他这个地方有路过,然后观察了一下,那是从这个地方漏出来的, 那我们待会要把它给拆解掉,要不然它可能会污染里面的限速呀之类的。啊,是就这个东西,那我们把它拆拆解掉, 然后取完之后呢,需要把这个两个螺丝直接把它取掉,然后取下来, 因为用手啊,喝这个酒他可能忘水多的话他会干,再来这个地方能不能放平一点给他漏出来,然后现在入烟火箭呢?那就是这个地方他会打入他这里面有两颗,然后这个地方有,这个地方有,然后我们把它拆掉, 然后呢用手把这个舌头压下来,然后用手呢下面手抬起来,好,现在就可以取出来了,现在就可以看到这个地方,就这个地方呢?呃,没分了, 这个地方也不能死,就就一颗直接直接拧开,好让我们亲爱的看一下啊, 那,那你看这边墨水已经满了,那他这个地方你看到没有?就墨水就是顺着这个地方一直往下,然后直接流动,那有时候这个地方毕竟这个地方有时候会限速,那他可能会把它污染掉,有时候会导致这个接触不良的这种。那我们把这个墨盒拿过去清洗一下,给它清空一下, 已经把他装回去了,然后把剩下的也都给他复原, 然后这个盒子以后装回去。这个盒子如果你装的你不知道, 你装上对了,他不是往里放就行了,如果你装上是错的,你把手拿掉,他自己会掉的,你装上,对了,他螺丝不用上刀,那他都可以暂时不会掉的。然后那,那这种装上那就是没问题。然后我们螺丝直接拿上去 啊?剩下的这个挂钩我要装回去,他这个地方你看到没有?一个洞,这个啥稍微摸索一点这个长处,长一样的螺丝粘上去。好的,这就可以了。

现在看一台佳能坡一百八色照片打印机的打印效果,哈,咱们改装连供的打印效果 看一看一下照片的原图,咱们选择的是 a 四的高质量打印高光照片纸啊, 打印一张全彩 a 四照片,最高分辨率,打印速度大概需要一分半左右。 一会看一下他的打印效果,看看他的打印。这款机器主要推荐给 照相馆和咱一年可以使用, 色彩非常逼真啊,非常。

拆开墨盒包装后,先撕掉透气孔的膜,然后摘掉墨盒的保护罩, 打开打印机盖子,等待车架移动到中间停下后,取出需要更换的墨盒,轻轻按一下墨盒前扣,墨盒就会弹起来,然后取出墨盒,最后将新的墨盒安装上对应颜色的墨盒槽内, 往下按压,扣紧墨盒,然后关上打印机盖子。新墨盒安装会提示无法检测墨水量, 我们根据提示连续按三次打印机的 ok 键清除错误,按了三次 ok 键后,最后提示按住停止重置键五秒, 然后我们按住打印机的停止重置键不放手,打印机面板跳转后松开手即可以屏蔽该错误,漠河就可以使用了。

佳能 ip 一百打印头更换,打开排机,打开前盖,等打印头移至中间, 去掉魔盒,往上一推,去掉魔盒,去掉大眼头, 往上一提啊,大眼头可以去掉。把准备好的新大眼头装上 好,下压好,准备好新的魔盒,装上黑色魔盒, 盖上盖,装上复印纸, 效果完美。

将能四二兼容漠河安装教程,首先漠河拆开包装后,上机前需将漠河的黄色导气膜撕开,黄色岛气膜撕掉后,把漠河的橙色保护罩按照箭头方向旋转拧开。 接着打开打印机机盖,正常情况下末车会自动移动到中间并停下, 取出需要更换的漠河,然后将荣威号裁漠河安装到对应的打印机槽内,漠河卡扣往下按压,用力按到位,直到听到咔嚓一下的声音。安装正确后,打印机漠河提示灯亮起, 更换完成,关闭打印机机盖,最后测试打印即可。

小车移动出去以后,首先要打开他的第一号盖,按住蓝色的卡扣往外掰,二号盖往上抬,现在可以看到打印头,打印头可以取出, 先打一头放入 合上他的二号盖,再合他的一号盖, 然后关闭上护照 机器吸引印墨,吸完印墨以后自己做打印头调整,如果未装纸会提示你装纸。

大家好,今天我们来修两台佳能 ip 一百的便携式一体打印机,首先我们来修上面这台,给它推到里面, 我们插上电线,打印一下测试液,检测一下故障,接通电源,上盖打开,摁一下电源键, 那个电电机器没有任何反应, 那么我们测一下这个试配器是否损坏, 机器标的是十六数,我们来测一下, 可以看到吧, 可以看到外用表是十六伏,说明我们的试配器是好的,那么故障应该在机器上,我们来拆机检测一下。 首先我们把这个上盖卸下来,这两边有两个卡扣,我们稍微这么弄出个弧度就卸下来了,放到一边, 后面有几颗螺丝,我们把这几颗螺丝都卸下来,这几颗螺丝都卸下来, 机器之前让其他的师傅修,已经把外壳撬花了, 用十字螺丝刀把这几个螺丝卸下来, 检查一下还有没有螺丝, 然后我们把侧盖扣下来,这嘎有一个活口,这样侧盖就拿下来了, 把右面灯也取下来,用个一字的小螺丝刀,轻轻 一翘就吓人, 这样我们就能把这几个卡扣打开, 这都已经敲碎了,这个好好打开,我们就能把扇盖拿下来, 忘了前面这还有三颗螺丝,能把这三颗螺丝线 中间的黑已经没有了,而且外壳已经损坏, 这样我们就能把上盖轻松的取下来, 这里还有很多死光,我把它卸下来, 对啊,上盖我们就能轻松的拿下来,不过我刚才拿的有点费劲啊。 我们来检测一下电源,这个是开机按钮,通过这排线,这一条排线到底下的电源板, 我们把需要把后壳也得拆下来,稍等一下,我们发现问题,在排线的这个地方我们可以看到断了, 应该是之前维修师傅给弄断的,所以说他不开机,但是这根排线我现在没有货,所以说这台机器今天只能这样,等货到了我再来拆卸他的安装方法, 那这个机器我们就放到一边修下一台,我们把这些拆开的螺丝和配件放好, 我们来看看这台机器,接通电源,打开上盖,按一下开机按钮, 可以看到电源灯已经亮了,而且机器有动作, 那么我们接上打印线,打印一张测试液,来看一下子机器的具体故障, 出几张第四支 装到禁止盒, 这么大一张测试液, 稍等一下,机器正在出石化,测试一二,我已经发送过来,你看机器不大,速度还是挺快的, 已经打印完毕,通过视频我们能看到只有蓝色的,其他颜色没有,尤其是黑色一点没, 那么我们通过驱动的清理软件来清理一下打印头, 我把笔记本拿过来吧,这样我给大家操作一下。首先我们从最开始的地方右键找到设置, 找到设备和打印机对象,找到打印机,点一下管理,点一下打印机属性 在上方,最后一下有个维护,我们点下维护,这里有清洗和深度清洗,我们先简单的清洗一下所有颜色,直行 机器现在已经在工作,我们稍等一下, 我们打一下子自检团, 可以看到红黄蓝都出来了,还是没有黑色,那么我们再强力清洗一下, 这有个深度清洗,我们点一下就可以了,彩色间已经出来了,我们就不需要所有颜色和彩色,只选黑色就可以,那么我们执行确定, 如果深度清洗两到三次还是没有洗开的话,那我们就不必要再清洗了,打人头就是堵死了, 如果有那种药水的话,我们用药水泡泡,装机以后如果要是正常,我们就继续使用,如果还是没泡开的话,我们只有更换一个新的打印机, 这小便携机器除了搓者轮好坏,还有一个打人头,其他的几乎没有。部长, 我们来检测一下喷嘴图案, 可以看到黑色出来了一些,那么我们再继续清洗一下, 退出点深度清洗黑色直行 确定, 我们把纸装一下, 时间稍微长一些,大家耐心等待一下。 机器提示墨水量低,我们打下喷子看一下 多少还是有点,这种情况我们再清洗一次应该就可以了, 执行一下子普通清洗黑色执行 确定,现在提示墨水量很少,建议更换一下。我先不管这提示,我们清洗完了打一个测试液吧, 多少还是有一些堵塞, 放一会再清洗一到两回应该就没问题了。 既然讲到这里了,我就给大家讲解一下怎么更换打印头的方法吧。把测试液放在一边,机器关稍等一下, 打开上盖,然后打人头跑到中间这个位置来, 卸掉两个墨盒,拔掉电源,按住这两个卡扣往里一送,这样就抬起上盖,我们就能把这个 打人头轻松的拿下来。那么我们既然拿下来,就直接换上一个新的, 这是一个不是新的大人头,是一个好的大人头。机器拆下来,这是之前旧的,我们把这个好的大人头上上 对准这个位置往下一摁,把这个卡架往下一压,装好两个漠盒,这样打印头就更换完成。我们接通电源,开一下机, 打一张测试液喷嘴检查, 由于纸的原因刮了一下打印刀,造出漏沫现象,但是我们可以看黑色的非常完美,彩色的完美。那么佳能 ip 一百编写是打印机清理打印头, 更换打印头的方法,我们就讲讲到这里,谢谢大家。

猜倾斜单元,第一步需要使小车移动出去旋转倾斜单元,白色齿轮这一块逆时针旋转,手轻轻的推着小车单元,直到小车可以移动。 ok, 好, 小车单页移动出去。拆升降电机,两颗螺丝一颗,两颗千叶,大约两颗螺丝一颗两颗限速拔掉, 全部平移平移出去。这两个拆掉拆掉往上隔一截。 come on, 一颗螺丝,两颗螺丝,然后整体整体扳着往下移,意思一下,螺丝拆掉以后 整体托住往外平移。

you proceed it's advisable that you download the user guide for your printer from the cannon website ensure that you have one cannon pf ten printhead ready and that your image prograf has a role of approved print media loaded this will be required at the last stage of the printhead replacement procedure at the user interface screen scroll down to the word maintenance then scroll down to the words head replacement the question do you want to replace print head will appear on the screen select? yes at the user interface screen you'll see a diagram instructing you to open the top cover while pressing this blue button in the center of the printhead lock lever pull the lever towards yourself until it stops then open the printhead locking cover by pushing it away from yourself until it stops now unpackage the pf ten printhead inside the package you will find a disposable plastic glove for your protection to easily remove the foil wrapping tear along this tear tab it is important that you only handle the printhead by this blue top handle never touch the nozzles, the metal contacts or ink supplies surface now lift the old printhead from the carriage by its blue handle holding the new printhead by its blue handle you may now remove the orange covers carefully insert the new printed into the carriage pushing it firmly in ensure that the nozzles, the metal contacts and ink supply surface do not touch the carriage pull the printed locking cover towards yourself to lock the printed then push the printed locking lever away from yourself until it clicks now close the top cover the image program will automatically go through several stages to finalize the installation of the new printed at the last stage of the process the image program will automatically start a printhead position adjustment process all done to。

小车移动出去以后,首先要打开他的第一号盖,按住蓝色的卡扣往外掰,二号盖往上抬。现在可以看到打印头。打印头可以取出。 先打一头放入, 合上他的二号盖,再合他的一号盖。 然后关闭上护照 机器,吸引印墨。吸完印墨以后,自己做打印头调整。如果未装纸,会提示你装纸。

佳能 ip 一百大按头更换,打开开机,打开前盖, 等单头移至中间,去掉磨合,往上一推,去掉磨合, 去掉大烟头, 往上一提好单头可以去掉。 把准备好的新大烟头装上 好,下压好,准备好新的魔盒装上黑色魔盒 装上红紫, 效果完美。


加了一百位开启声音大,不然拍不了,受不了 mister difficult 抖音。

hi, i'm gordon from camera labs in this video you're going to see an exclusive teardown of a new canon rf lens and a peek into their latest optical technology in manufacturing if you've ever been curious what goes on inside a modern lens this is the video for you normally camera companies can be quite secretive about their designs and in 30 years of technical journalism i've rarely had any official access to the actual manufacturing processes beyond occasional factory visits with anxious managers ensuring we don't look too closely so when canon reached out and asked if i'd be interested in filming one of their engineers disassembled new lens in close up detail and explain exactly what's behind their latest optical designs? i said yes, please now this video isn't sponsored by canon it's just a rare opportunity to look behind the scenes which i thought would be interesting to anyone whose into lenses regard of the system that you use so thanks to canon for the invitation and let's get started our specimen today is the canon rf 28 mill f 2.8 stm a pancake lens announced in made 23, which uses some pretty interesting new types of optical elements to achieve its compact size and weight all lenses start with the design brief setting out not just the focal length and aperture, but also the target quality the approximate size and weight and of course the design price point for this model kanam wanted to produce a compact and affordable pancake lens for the rsr mirrorless system and 28 mill was chosen as its a flexible focal length for stills photography and video on both full frame and cropped apsc systems trouble is though the shorter back focus distance of mule as cameras compared to dslrs presents an optical challenge for wide lenses if you don't do it right, you'll suffer from greater softening and darkening towards the corners the diagram on the left shows the earlier ef 40 millimeter f 2.8 lens designed for the longer flange distance of dslrs notice the fairly shallow angle of the light ray as it strikes the extremes of the sensor now on the right look what happens if you try to use the same optical formula for the shorter flange distance of a mirrorless camera the angle of the light ray becomes larger resulting in greater darkening and softness towards the corners to reduce the angle at the extremes you need a new optical design with some unconventional looking elements here's canon solution for the rf 28 where a series of three large aspherical elements towards the rear of the lens work together to deliver much shallower light ray angles the largest element of all at the rear is only possible thanks to the diameter of the rf mount, but proposing a design is only one half the story now you need to actually make these unusual elements in practice again, while attempting to meet the target weight and price point the rf 28 2.8 design employs three a spherical elements so called as their shape is not a section of a simple sphere or cylinder modern lenses often employ a spherical elements alongside more conventional spherical ones to reduce issues like spherical operations but there's actually several ways to make them cannon has four different ways of producing a spherical elements depending on the target quality weight price and the actual complexity of the shape itself a typical lens could include elements made using several of the following techniques the first and most traditional option is to grind the shape cannon typically grows fluorite crystals then grinds them into the desired shape which can produce very high quality results, but they're also heavy and expensive to make so generally reserved for their flagship l series lenses the second technique is replica aspherical where a normal spherical element is bonded with a resin layer to give it an aspherical shape 34th use molding techniques to shape molten glass or plastic resin into the desired aspherical shape these allow often complex shapes to be produced at a low cost and thereby are a popular option in consumer lenses again the final lens design could include a combination of elements made using these different techniques in order to meet the target brief of the four techniques plastic molded elements or pmos, may seem like a basic approach, but by injecting optical grade resin into a precision mode then hardening it with uv light you're able to easily make elements that wouldn't be possible with glass molding or prohibitively expensive with grinding techniques indeed the rf 28 2.8 3 largest focal elements are all produced using plastic molding and allow it to not only meet the target price weight and size, but also deliver high quality results than you might expect while pmos are a fairly modern technique for producing elements cannons actually been using them in many of its lenses for some time now in fact most of the more affordable lenses in the rf lineup employed pmos in their optical designs including the sixteen two point eight fifteen to thirty twenty four to fifty twenty four to one of five s t m twenty four to two forty twenty four one point eight, fifty one point eight and one hundred to four hundred as well as the festal lenses designed for crop tpsc bodies going further back still pmos were also used in the efm 1855, 18150 and 15 to 45 as well as the efs 18 to 55 and 18 to 135 so they've actually been around for some time and most canon owners have probably had at least one in their collections in fact pmo's first counting for cannon was in the snappy 50 back in 1982, the use of plastic molding also allows you to easily produce squared off rectangular shaped elements allowing lens designers to not only reduce weight but reclaim space occupied by redundant portions of a traditional circular element remember your sense from photos are rectangular to technically there's no need for all the elements to be circular of course you could also grind a glass or fluoride element into a rectangle, but it would add to the cost versus a mold element where it's produced at the time of injection so let's now see how all this theory is put into practice by disassembling the rf282.8 and seeing not just those unusually shaped elements, but how the space savings been put to use the lens was taken apart by shinsukito from canon who guided me through each step in component the entire process took roughly half an hour, but i have sped up sections here okay, so the first step is removing the lens mount there's four screws to remove after which you comprise the metal mount from the barrel note the damage of the rf mount is what allows those large rear elements which in turn provide great flexibility and optical design after popping out the central baffle section you can remove the external decorative ring now you can see the main circuit board for the lens along with the ribbon cable leading to the 12 pins which used for communication with the camera body the rf mount allows much faster data communications in the older ef mount in turn enhancing things like focusing up to control and stabilization not to mention supporting additional controls you can also see the shape the circuit board is exploiting the space that's freed up by those rectangular lens elements and as partly what's allowing a more compact lens barrel after unscrewing and removing the circuit board is possible to unscrew the external barrel due to the size of the lens this is a fairly short cylindrical section put its home to the main switch allowing you to select manual or auto focus or assign the focusing ring to a custom control next is to remove the stm focusing motor itself a tiny component that again slips into the space free by the rectangular lens elements accommodating focusing motors is a key challenge for lens designers so the chance to exploit any space space is welcome cannons used a gear type stepping motor here for size smooth operation and fast response next shin prizes off the ring printed with the lens name and spex has seen from the front and now for what shin calls the fixed barrel, which surrounds much of the lens group, which has become progressively exposed during the physical disassembly the lens is then turned round to remove the filter barrel held in place by three screws as its name suggests this is used to mount filters and as a side note it's interesting how on modern mirrorless lens designs the larger elements are now often at the rear of the lens leaving a relatively small one at the front and that's the opposite to many dslr lenses that we're used to next the lens group is removed from the focus barrel and ashun turns this from the side you'll see the helical grooves used to shift the required lenses while focusing now finally we can take part the main lens group starting with the protection glass, which represents group 6 next comes group 5 which consists of a single large plastic molded a spherical element and from the reflections you can see this is the one with the seagle profile and again notice its rectangular shape nection removes the first of several tiny collars these were adjusted on each lens to fine tune their performance at the factory and ensure the optics are perfectly lined up the first lens group can now be separated to reveal the electromagnetic die fram or emd for short this is what adjusts the lens aperture and while it's operated electronically by the camera in normal use is possible to demonstrate the opening and closing mechanism with the right tool this iris on rf lenses can also be adjusted in very fine increments to minimize visible steps and exposure while filming video after removing another adjustment colour the section containing the second and third optical groups can be separated and after peeling off a ring you can see the third group and this consists of another plastic molded aspherical element note, how this one is circular this leaves one final group and if you've been counting you'll know it's group four again containing one plastic molded aspherical element and like group five it's a larger more complex shape with squared off corners this leaves the guide barrel as the last part of the disassembly process let's now take a closer look at the elements laid out in group order starting with the group which consists of two glass elements next his group two which also contains two glass elements now his group three which consists of one element and it's the first of the three plastic molded or piamo aspherical elements next in group four is the second pmo and notice how it's squared off and after that it's the rear most fifth group containing another single pmo that's also rectangular in shape these five groups of seven elements make up the main optical construction of the lens, but there's an additional covering element to the very rear representing a sixth group let's take a closer look at the three main plastic molded as focal elements and as shouldn't angles them to catch the light you'll notice the reflections revealing their unusual shapes in particular, the two squared offers spherical elements, employ, almost, wing light profiles not similar tip say a seagle and fly tor perhaps an elaborate moustache i love looking at reflections in lenses and some of these remind me of the black hole in interstellar anyways these shapes that are allowing compact wide angle mirrorless lenses to deliver well corrected results into the corners despite the short flange distance and i believe cannon is one of the first companies to produce this kind of element for a mass produced lens and while you could in theory grind them out of fluorite or other elements it again would be difficult expensive and in some cases completely impractical indeed plastic molding was primarily chosen here as the best way to achieve the actual complex shape with the added benefits of being lighter and more affordable while also providing the opportunity first squared off shapes cannons also making bold claims about the performance with the rf 282.8 mtf chart looking pretty respectable against the high end rf twenty eight seventy f two l zoom at twenty eight mill or be it open to f two the rf twenty eight two point eight seventy f char also compares favorably against nikon's recent z twenty six two point eight and while the dimensions and weight are similar cannons is also coming in cheaper in my thirty years of reviewing camera gear i've learned it's important to approach new materials, technologies and techniques with an open mind and the bottom line is while high end lenses like cannon's l series will continue to grind fluoride elements for some time plastic molded elements are allowing more compact and affordable designs that literally punch above their weight of course the proof of the pudding is in the eating so i'll be thoroughly testing the rf 28 2.8 as soon, as i get hold of a reviewable sample to see if it lives up to expect take make sure you subscribed with notifications so you don't miss out on that or any of my other in depth reviews in the meantime, i hope you enjoyed this technology backgrounder and thanks again to cannon for the opportunity to peep behind the scenes of their latest lens designs and of course shin's expert skills at taking apart the lens now all i have to do is figure out how it all fits back together again, thanks for watching and i'll see you next time bye bye。

这是一款佳能的一百到四百,所呈现的故障是变焦正常,无法自动对焦,释放快门对焦没有任何的反应,手动对焦磕头窗也没有任何的变化。我们现在开始拆,打下卡扣上面所有螺。 拆到这一步,我们发现镜头的一个镜筒是已经变形了,这个镜头肯定是摔过。我们继续检测。 拆下镜头,现在看到的是镜头的超声波马达。取下超声波马达,这是镜头的超声波马达, 我们可以看一下超声波马达的工作呢,并没有任何的问题。手动波动这个对焦感呢是正常的,能左右摇摆就属于正常 超声波马达。通过电机来控制对焦杆,对焦杆呢是需要卡在手动对焦环的,这个对焦镜的一个控制白轴,我们现在可以看一下,波动的是非常的吃力的。像这种情况有可能是镜头的对焦组变形。我们开始继续拆。

今天修一只佳能一百到四百吸尘器,打开卡口,取下脚架环,抽出后镜头,再抽出内镜头,抽出对焦马达组件。 看到吸尘器了没?把灰尘通过滑轨吸到镜片,拆掉前阻镜片, 所有的灰尘都在这里了。