用纸做枪的弹壳可以装弹的教程

回弹枪展示天第一步开始组装， 装一发子弹，再将子弹推上膛， 老铁看懂了吗？ 的结构还算比较简单吧？原理简单一些，但是离抛壳的原理不算太远了，我再给他简化一下。然后呢，再给老铁出教程。

你还记得这把刀是怎么折的吗？这是你的童年吗？拿五张背四纸对折，然后裁成十张纸，有条件的建议直接十张背四纸，拿一张纸沿着长边两次对折，像这样一共折八个一模一样的出来。 然后拿一张纸来做枪芯卷纸，用这种方法搓出来又快又好。然后用固体胶把卷纸粘紧， 以吸管为芯，搓一个粗管做枪管，试一试吸管能不能在粗管里自由活动。把粗管粘紧，记住搓一下就好。然后开始组装， 我们要保证粗管能穿过去， 像这样的我们需要三个 纸条，这样折一下能更好的操作， 一定要用胶布使劲固定好，不然晚几次就会掉。有条件的用订书机进行加固， 建议橡皮筋缠在这个位置比较好，这样腔体就做好了。开始做子弹， 把子弹捏一捏，让他变成圆柱体。

上糖啊。哦，可以拉出来的哦。 哇塞，嗯，放了几天呐？两天。

内十指裁剪一半，用竹签卷起来， 像这样卷两根细管，再用细管沿一四指短边卷，卷松一点。细管拿出来，像这样卷三根粗管，四指延长边卷起来，像这样卷细一点，共六根。用一根粗管平均分五段， 依次对齐，粘在一起，像这样就可以了。 再拿一根粗管，剪出九厘米，像这样左对齐，粘住。用第三根粗管剪出十九厘米，与下边五根又对齐粘住两厘米，粘住纸条对折， 对折，再对折， 粘在这里就 ok 了。 拿出一根吸管，留出两厘米折吧。泡上皮筋，用胶带粘住， 像这样插进管理。泡上皮筋，用第二根细管左对齐做标记，再向左两厘米标记并掰弯。再向左一厘米掰弯 做标记，标记处向左约两厘米挂第二个标记，沿第二个标记剪套。皮筋 对齐，站在扳手前端，顶住 最长一根，压扁对齐，像这样不停的折，继续折， 像这样把轮廓固定好。嗯，好看多了，上膛。

这里绕的相对松一点， 把面也一样塞进去， 折出两个正方形， 从中间这个正方形的中心拆开， 分成三等份。 这里绕的稍微松一点， 打开露出四个歌 塞进去，组装到一起。

听说大家在找九八 k 要抛壳的，还要能发射的，看看这个行不行？

shot shells are loaded into the magazine through the bottom of the receiver the compressed magazine spring keeps tension on the shells pressing the action bar lock allows the fore end to be pulled to the rear as it comes back a shell is fed into the receiver forward on the fore end lifts the shell and the bolt guides it into the chamber as the fore end moves back a cutout on the bottom of the slide engages the carrier dog as the slide moves forward downward force is put on the carrier acting as a lever to lift the shell up the left and right latches allow shells into the receiver under the control of the fore end tube assembly notches on the assembly move the latches in and out at specific times the left latch holds the shell until the fore end is almost fully rearward after the first shell advances into the receiver the right latch catches the next shell as the fore end is pushed forward the first shell is moved into the chamber and the left latch assumes control of the next shell when the bolt makes contact with the breech face the slide pushes up on the locking block locking it into the barrel with the safety in the off position the trigger is free to move pulling the trigger rotates the sear which releases the hammer the hammer strikes the firing pin causing it to travel forward and impact the shell primer the inside of a shot shell contains a primer powder charge a wad and shot or a slug inside the primer is a primer cup priming compound and an anvil as these are struck by the firing pen a chain reaction ignites the powder charge inside the shell and the wad is propelled down the barrel just after leaving the barrel， the wad opens so the shot can spread the extractor grips the rim of the spent shell case as the fore end is pulled to the rear the bolt is unlocked and the case is extracted from the chamber， the bolt continues to the rear and the ejector kicks out the empty case from the receiver as the bolt comes back the hammer is reset and held back by the sear when the fore end is fully forward the action bar lock lowers the connector again allowing control of the sear with a pull of the trigger。

做的手工是一把枪，他可是他是可以发射子弹的。 首先先拿拿一颗子弹，然后呢，把这里拉一下，把子弹塞进这个这里面的吸管里， 然后这里是可以看过去的，也可以对着他瞄准，按下反击不对。

自动退壳枪不但能自动退壳，还能发射纸袋。