粉丝2.2万获赞28.9万



place the car seat base in the back seat of your vehicle unfold the load leg if using next check the base angle if the angle indicator is not correct adjust the base the adjustment handle is at the back of the base squeeze the adjustment handle lift or lower the back of the base then release the handle so the base foot locks into a position the angle indicator will turn completely green when correct no red should be showing next lift the release lever you must lift the release lever in order for the latch lower anchor belts to loosen now release the lower anchor connectors from their storage location press in the red button push the connector into the storage location then pull it and the belt out now attach the lower anchor connectors to the vehicle anchors review your vehicle owners manual for latch lower anchor locations and latch lower anchor use next push the release lever down you must push the release lever down in order for the latch lower anchor belts to tighten then push down on the base to tighten the lower anchor belts the belts will begin to automatically retract and tighten as you push down now check the tightness indicators the red will turn completely green when tightened correctly no red should be showing the final step is to extend the load leg squeeze the buttons on the load leg and pull it down until it meets the vehicle floor release the buttons lift the front of the base while holding the load leg in place to lock it into position it must be perpendicular to the vehicle floor now the base installation is finished this step is to install the inner and outer carriers on the installed base align the slots on the sides of the outer carrier with the lock bars in the base push down, firmly on the sides in front of the outer carrier to lock it into the base pull up on the front two corners of the outer carrier to make sure it's locked into the base then install the inner carrier to the outer carrier pull up on the front two corners and the back of the the inner carrier to make sure it's locked to the outer carrier the carry handled must be locked and in position one or position two lastly re check the angle indicator on the base to make sure it is correct。


大家好,我是仓鼠,今天我带大家来看一下我们迈克士的睿智小巨人,也就今天 polo 这一款的一个安装, 这个就是我们的一个爱车被子接口,有的是在那个靠背和坐垫那个缝隙里面,有的呢就是直接裸露出来的,有一个引导槽,这个是我们车座椅上的一个接口杆,握住这个以后拉出我们的接口杆非常轻松。好的,另外一端也是一样的, 然后我们的接口杆对准我们接口槽里面的接口环推进去就 ok 了,非常简单。 我们刚才安装了我们下面的两个接口杆以后,我们就找到他的上搭带,就拖布连接带,然后找到汽车靠背 背后的一个挂钩猫点的位置,然后直接挂上,挂上以后,然后我们再收紧这个上拉带,收紧这个皮带就就 ok 了, nice。

安全带啊,你看这反了,你看揪在一起了,我们怎么弄呢?我们把这个,把这个插头折叠一下,看把安全带折叠一下,这样这个安全带就纠正了, 两边都是同样的原理。看一下,你看好像揪在一起了,是吧?就折叠在一起了,我们把折叠一下,折叠一下,把它弄过来,弄过来让你试一下。哎,还是折叠的,你看我们再折叠一下,折一下,往下抹一下, 好把它弄正好。弄正。你看这个,这个时候两个插头就就恢复正常了,这个就是他的一个安全带折叠在一起了, 怎么把它恢复正常?好?嗯,很简单的。