粉丝1134获赞3663

孵化机器有两种情况下需要恢复出厂设置,第一种情况孵化温度不准确的时候,需要通过恢复出厂设置来矫正这个孵化的温度。第二种情况是孵化板一批种蛋进行,第二批种蛋进行孵化的时候必须恢复出厂设置。我们家的每一款机器上面都有一款这样的智能控制面板, 怎么恢复出厂设置呢?同时按着面板上的加减或者是增加或减少键三秒钟, 等到显示屏上显示三个八的时候,恢复出厂设置成功。


呃,你好,我们呢录一期那个欧姆龙的 u e c 这款,咱们恢复出厂测值,首先咱们按下这个旋转跟那个框键,去一下内置插座里面, 然后出现这个值过后,咱们不用调这个是没锁定的,咱们把这个值改成零,因为一是代表锁定吗?零是代表解开,然后打开过后,然后咱们按一下旋转跟那个框键,然后返回到就是温度页面, 然后到这个页面过后,咱们按下框键,按三秒,然后继续按这个旋转键,然后找到那个,嗯,给你看一下,对,找到这个 r m 的这个菜单,然后咱们把它改成负的幺六九 九,对吧?然后按一下下键,然后按下这个 pe 可以切的,对吧?按到一这里,然后再按一下 pe, 再按一下,然后把它改成九,然后再按一下这个 pe 键,然后改成六, 对吧?咱们改成这个值过后,咱们首啊,然后出现这个值过后,咱们按下上键,按下这个值,然后就是恢复出厂了,然后如果还是选择 off, 那就是, 呃,按这样,然后就恢复出厂了,然后咱们就直接可以退出来,按下这个框键,再下框键就退出页面了,然后这个就是恢复出厂设置过后的一个一个表了。

hey guys victoria here with streamin support bringing you a super quick tech corner tutorial today, i'll be showing you how to perform a factory reset using big sky timeline and mobius with all the different presets and settings that these pedals have sometimes a factory reset is helpful in creating new tones from scratch so let's dive in first let's start with resetting the presets this will erase all custom presets and restore them to the factory ones please keep in mind that this is permanent and cannot be undone first start with the pedal disconnected from power then connect the power to the pedal while at the same time pressing down on the a and c foot switches on big sky or the a and tap foot switches on timeline and mobius wait a few seconds until the display reads complete at this point the factory presets are now loaded disconnect the pedal from power once again and reconnect it to start using there's also a second reset procedure specifically for resetting your global setting such as your midi channel spill over setting bypass setup and more for this reset start with the pedal disconnected from power then connect power to the pedal, while simultaneously pressing down on the type and coder button wait a few seconds while the display reads r cplt your global settings are now reset to their factory setting disconnect the pedal from power once again and reconnect it to start using i hope this short tutorial has been helpful if there's anything else you'd like us to cover in the next time corner please let us know by dropping a comment below or shoot us an email to support at stryman net thanks for watching。

教大家这个智能锁,像这种新款新型的智能锁,请自动的如何恢复出厂设置,如何重置了吗?这这个锁呢?你看像我们这款锁,它是三 d 人脸识别的,它这个是,你看摄像头,这个是猫眼摄像头, 他是带猫眼功能的摄像头,但是他他就我们转转过来以后,你看我们这个就是猫眼,是不是啊?他他是可以监控外面的猫眼摄像头,但是我们把电池拆了,就这些地方全部拆掉以后,他也是找不到那个恢复出厂设置的按钮的, 你看我们现在把它把它拆拆开,我们全部全部拿开啊,近一点,你看是不是这些地方都没有恢复出厂设置的按钮,你看下面这些地方,他也是没有,对不对?就这种要 如何操作?我们就还是要把 先把电池装上以后这种怎么操作的?你看他这个这里是不是有个开锁键?你看这个是开锁键,他是不是开锁了?这颗是上锁键,这个键上锁键,你看他是不是上锁了? 我们让他停止以后,我们同时压住这两个上手机跟开锁键,压住九秒钟即将恢复出厂状态。按警键器件,看到没有?请按新键,他说叫你叫我按井号键恢复出厂设置。初始化成功,是不是?初始化成功了? 是不是非常方便?但是如果我不教你的,你永远都找不到那个恢复出厂车子的按钮,是不是非常方便的?

哎,胖虎,你又搁这思考啥人生呢呀?我三十二寸的甲细愣生生给我用成二十四寸,怎么短了两块?你瞅瞅这咋回事啊? 你笨呀,你调一下分辨率啊,我都调好的呀,看到没有?正常的呀,这咋回事啊?你肯定是手欠,不小心碰到嫌弃了。那给他恢复一下出厂设置就好了。来,我教你 每款显示器呢,在这个侧边或者说下边都会有一些按钮啊,每个显示器都不一样。然后就拿我这个来说,咱们先给他找到这个菜单了, 看一下,先找到菜单了,然后边看着边挑,找到这个找到找到这个,重置看到没有,然后确定好了。这就好了,你学会了吗?
